 | | Re: Tangent between two circles in 3D space?
|
|
(...) What you really need is to find a way to find just one side of the "rubber band". Say, pulley A to pulley B, "Side one". Then you could use the same function to determine pulley B to C, side one or two, and so on... Right? Paul (22 years ago, 24-Jan-03, to lugnet.cad.dev)
|
| |
| | Re: Tangent between two circles in 3D space?
|
|
Kevin, I have been watching this thread with great interest and it is really fun to watch the community pitch in and assist you. Would you do me a favor. When you finally have the solution, could you summarize in a post? I plan on using this as a (...) (22 years ago, 23-Jan-03, to lugnet.cad.dev)
|
| |
| | Re: lsynthcp community development project setup on sourceforge
|
|
(...) I couldn't find it anywhere in this thread, so the project page is here: (URL) on the Browse CVS link near the bottom to view the source code. The homepage is here: (URL) just to test things out a bit, I logged into the sourceforge compile (...) (22 years ago, 23-Jan-03, to lugnet.cad.dev, lugnet.cad.dev.mac)
|
| |
| | Re: Tangent between two circles in 3D space?
|
|
(...) This looks great! This is what I was trying say the other day during my ah,hah! moment, but not so tersely. Now I just need to know how to calculate the intersection of the line and each circle and I'll be all set I think. I'll do some (...) (22 years ago, 22-Jan-03, to lugnet.cad.dev)
|
| |
| | Re: Tangent between two circles in 3D space?
|
|
"Kevin Clague" <kevin_clague@yahoo.com> skrev i meddelandet news:H92o0p.CGB@lugnet.com... (...) a (...) Line = Intersect(C1.Plane, C2.Plane) if (Dist(C1.Center, Line) = C1.Radius) and (Dist(C2.Center, Line) = C2.Radius) ... (Or have I (...) (22 years ago, 21-Jan-03, to lugnet.cad.dev)
|
| |
| | Re: lsynthcp community development project setup on sourceforge
|
|
Agreed! -- Steven B. Combs, Publisher Bricks in my Pocket (BimP) (URL) Submission Information: (URL) member #414 "Kevin Clague" <kevin_clague@yahoo.com> wrote in message news:H92o80.D83@lugnet.com... (...) question! (...) (22 years ago, 21-Jan-03, to lugnet.cad.dev)
|
| |
| | Re: Tangent between two circles in 3D space?
|
|
(...) More or less... there are 4 tangents to the 2 cylinders that happen to be on the circles. (...) Some thoughts that could perhaps (with [lots of] work) lead to an iterative solution: - Select one of the circles, then choose one radius of this (...) (22 years ago, 22-Jan-03, to lugnet.cad.dev)
|
| |
| | Re: Tangent between two circles in 3D space?
|
|
(...) Yes. This *is* the ultimate (and probably universal) solution, although we probably need to be able to find one of four cylinders between any two circles in 3D space. You are thinking in terms of pulleys always on the outside of the band. With (...) (22 years ago, 22-Jan-03, to lugnet.cad.dev)
|
| |
| | Re: Tangent between two circles in 3D space?
|
|
Hi Kevin, I think common tangent to circles is too restrictive, since rubber belts tolerate quite a lot of misalignment. ((URL) the problem should be reformulated as: Two circles in 3D space define two cylinders orthogonnally extruded from them. (...) (22 years ago, 22-Jan-03, to lugnet.cad.dev)
|
| |
| | Re: Seam width
|
|
(...) Please see (URL) (22 years ago, 22-Jan-03, to lugnet.cad.dev)
|
