 | | Re: Part description help request
|
|
(...) For the CATEGORY, I recommentd either "Boat" or "Minifig Accessory". Depending on which CATEGORY you use, that will determine the first word of the DESCRIPTION. For KEYWORDS, I recommend the following: cannon, cannons, cannonade, "black (...) (24 years ago, 3-Dec-00, to lugnet.cad.dev)
|
| |
| | Part description help request
|
|
Hello everyone, I am just about finished with two new parts. The "Pirate" cannon (then non shooting one) and it's base piece. I would like some suggestions on a good part description, keywords and a category. They are available for viewing at my "in (...) (24 years ago, 3-Dec-00, to lugnet.cad.dev)
|
| |
| | Fiber Optics module
|
|
Has anyone else noticed that the axle hole on this .dat file is 2 ldu higher than it should be? It would be great if someone else with this part could confirm this. -John Van (24 years ago, 3-Dec-00, to lugnet.cad.dev)
|
| |
| | Re: LDLite status (was Re: LDLite center offset problem?)
|
|
Steve Bliss skrev i meddelandet <5e0g2tsbp71mhhjc9d6...ax.com>... (...) I have used the source (Pascal port of early version) in my LDList program, and LDLite is the default viewer for .dat-files on my computer. (...) Just scaling up/down is not (...) (24 years ago, 1-Dec-00, to lugnet.cad.dev)
|
| |
| | License - again
|
|
Last time we talked about a license for the parts library we couldn't reach an agreement, so here I am again trying to wrap this up. I know this is a boring subject but let's try to reach an agreement. I don't think we need to write a long license, (...) (24 years ago, 2-Dec-00, to lugnet.cad.dev)
|
| |
| | Re: numbers for "Castle" minifig torso patterns?...
|
|
(...) I'm still not sure about using 'S' for this, because S01 is commonly used for parts/s/ files. But I definitely agree with the idea. (...) Erk. Doesn't LEdit cut off file-references that a too long? (...) Authors have got to be careful to (...) (24 years ago, 1-Dec-00, to lugnet.cad.dev)
|
| |
| | Re: LDLite status (was Re: LDLite center offset problem?)
|
|
(...) I use LDLite (mostly) in conjuction with LDAO (to generate the VEC images, and the HTML instruction images) and to generate the images for Partsref. Some things I'd like to see: 1. LDLite 2.0 doesn't crop saved images to the edges of the (...) (24 years ago, 1-Dec-00, to lugnet.cad.dev)
|
| |
| | Wizard Beard part
|
|
Anybody working on this part, or have it done?... Thanks, James Wilson (24 years ago, 1-Dec-00, to lugnet.cad.dev, lugnet.cad.dat.parts)
|
| |
| | Re: LDLite status (was Re: LDLite center offset problem?)
|
|
(...) As I have pointed out before, this is my most wanted feature upgrade of LDLITE nowadays. It looks a bit odd to see rendered images where the type 2 lines are 3 pixels wide, while the type 5 lines are plain one pixel wide. The other things you (...) (24 years ago, 30-Nov-00, to lugnet.cad.dev)
|
| |
| | description error in 2434.dat
|
|
it should read studs on sides not stud on sides (24 years ago, 1-Dec-00, to lugnet.cad.dev)
|
