 | | Re: *** LDView Version 1.9.1 Released ***
|
|
(...) A few notes on compiling it from the source: I had to copy the libpng debug files *after* the zlib debug files to get it to link because the zlib files overwrote vc60.something that it seemed to need. Where did you get your wglext.h and (...) (23 years ago, 28-Jan-02, to lugnet.cad, lugnet.cad.dev)
|
| |
| | Re: Parts Tracker update frequency
|
|
(...) I prefer a regular update, on a month base or so. This has some advantages, as some parts will be faster released than on a volume base, and the files to download will be also less large than on a volume base. Anyhow, every method has his pro (...) (23 years ago, 28-Jan-02, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Parts Tracker update frequency
|
|
(...) Thanks for the update, Steve I think I'd prefer the "volume method", though it's not something I'd die for 8?) ROSCO (23 years ago, 28-Jan-02, to lugnet.cad.dev.org.ldraw)
|
| |
| | *** LDView Version 1.9.1 Released ***
|
|
LDView version 1.9.1 is now available, in both source and binary forms. You can download either from: (URL) note that the 1.9.x set of LDView releases are all development releases. Consequently, they are likely to be less stable than version 1.0. (...) (23 years ago, 27-Jan-02, to lugnet.announce, lugnet.cad, lugnet.cad.dev)
|
| |
| | speargun??? (already encoded?; part number?)
|
|
Hi, Has anyone tackled the minifig Speargun yet? If so, would you please direct me to the correct place? (URL) Also, what's the "official" part number for the speargun? Thanks, Franklin ===== Franklin W. Cain Programmer for Hire "fwcain@yahoo.com" (...) (23 years ago, 27-Jan-02, to lugnet.cad.dev)
|
| |
| | Re: Steve?...
|
|
(...) This week has been a little busy. And I didn't want to do a lot of work in the Parts Tracker until I was sure it was stable and ready for use again. Steve (23 years ago, 27-Jan-02, to lugnet.cad.dev.org.ldraw)
|
| |
| | Steve?...
|
|
Steve, I haven't heard back from you on this, yet... Thanks, Franklin (...) (23 years ago, 27-Jan-02, to lugnet.cad.dev.org.ldraw)
|
| |
| | Steve?...
|
|
Steve, I haven't heard back from you on this, yet... Thanks, Franklin (...) (23 years ago, 27-Jan-02, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: JAVA - Viewer for dat-Files
|
|
Travis Cobbs wrote: > (Follups sent to lugnet.cad.dev.) > > In lugnet.cad, Kyle McDonald writes: > >>I'm curious if any of you OpenGL/LDraw guys do much in your code >>to generate strips from the DAT files to improve performance? I think >>I have (...) (23 years ago, 26-Jan-02, to lugnet.cad, lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Re: JAVA - Viewer for dat-Files
|
|
(Follups sent to lugnet.cad.dev.) (...) Well you have to careful when you do this. The problem with strips and fans is that they can only be used for smooth surfaces. You only get one surface normal for each point, so any faces connected to that (...) (23 years ago, 26-Jan-02, to lugnet.cad, lugnet.cad.dat.parts, lugnet.cad.dev)
|
