| | Part description help request
|
|
Hello everyone, I am just about finished with two new parts. The "Pirate" cannon (then non shooting one) and it's base piece. I would like some suggestions on a good part description, keywords and a category. They are available for viewing at my "in (...) (24 years ago, 3-Dec-00, to lugnet.cad.dev)
|
|
| | Fiber Optics module
|
|
Has anyone else noticed that the axle hole on this .dat file is 2 ldu higher than it should be? It would be great if someone else with this part could confirm this. -John Van (24 years ago, 3-Dec-00, to lugnet.cad.dev)
|
|
| | Re: MOTM entrance question
|
|
I would trust you. Terry K <legoverse@yahoo.com> wrote in message news:G4yK5F.8F5@lugnet.com... (...) some (...) Or (...) (24 years ago, 3-Dec-00, to lugnet.cad.dev.org.ldraw)
|
|
| | Re: MOTM entrance question
|
|
"Terry K" <legoverse@yahoo.com> wrote in message news:G4yK5F.8F5@lugnet.com... (...) some (...) Or (...) I wouldn't have a problem with it. -- Tim Courtney - tim@zacktron.com (URL) - Centralized LDraw Resources (URL) - Zacktron Alliance ICQ: (...) (24 years ago, 2-Dec-00, to lugnet.cad.dev.org.ldraw)
|
|
| | MOTM entrance question
|
|
Hi all, Just a quick survey of opinion. Given the fact that I oversee the voting, is there any objection to me submitting an entry in the MOTM? Am I trustworthy enough to handle it, or would it be preferable to have some oversight of the results? (...) (24 years ago, 2-Dec-00, to lugnet.announce, lugnet.cad, lugnet.cad.dev.org.ldraw)
|
|
| | Re: Winner of the December 2000 ldraw MOTM is.......
|
|
(...) The parallels to the US election are just *too* sweet:-) But I see that this time the Gore gone won. <g, d, r> -John (...) (24 years ago, 2-Dec-00, to lugnet.cad.dev.org.ldraw)
|
|
| | Winner of the December 2000 ldraw MOTM is.......
|
|
Hi all, I was going to do this later, but won't have time, so mid-Saturday it is. The winner for December 2000 is "the Gorgon" by William Fitzgerald. (URL) William for a very cool model. Most all the entries did pretty well, but William had a clear (...) (24 years ago, 2-Dec-00, to lugnet.announce, lugnet.cad, lugnet.cad.dev.org.ldraw)
|
|
| | Re: LDLite status (was Re: LDLite center offset problem?)
|
|
Steve Bliss skrev i meddelandet <5e0g2tsbp71mhhjc9d6...ax.com>... (...) I have used the source (Pascal port of early version) in my LDList program, and LDLite is the default viewer for .dat-files on my computer. (...) Just scaling up/down is not (...) (24 years ago, 1-Dec-00, to lugnet.cad.dev)
|
|
| | License - again
|
|
Last time we talked about a license for the parts library we couldn't reach an agreement, so here I am again trying to wrap this up. I know this is a boring subject but let's try to reach an agreement. I don't think we need to write a long license, (...) (24 years ago, 2-Dec-00, to lugnet.cad.dev)
|
|
| | Re: numbers for "Castle" minifig torso patterns?...
|
|
(...) I'm still not sure about using 'S' for this, because S01 is commonly used for parts/s/ files. But I definitely agree with the idea. (...) Erk. Doesn't LEdit cut off file-references that a too long? (...) Authors have got to be careful to (...) (24 years ago, 1-Dec-00, to lugnet.cad.dev)
|