| | Type-5 conditional edge line
|
|
I have a question about the type-5 conditional line. Assume I have four points in 3d space like this: (If you're reading LUGNET via the web interface, you must push "view raw message" to see my ASCII art.) 1---2 | | | | | | 4---3 Except that the (...) (25 years ago, 1-Apr-00, to lugnet.cad.dev)
|
|
| | PIPE function... [DAT]
|
|
I've made a new function for LDS called PIPE. It's an extension of the LINE function. Remember:? LINE POINT x y z POINT x y z ... POINT x y z LINE END Now, PIPE works the same way but with that difference it's in 3D: PIPE [n_sectors total_sectors] (...) (25 years ago, 1-Apr-00, to lugnet.cad.dev)
|
|
| | Re: What is BFC meta command ?
|
|
(...) What if I am creating a new part? Regards John (25 years ago, 1-Apr-00, to lugnet.cad.dev)
|
|
| | Re: BFC: LITS 2
|
|
Steve: (...) No. - Or rather: That depends on how good looking a rendering you want. Thinking a bit more about it, I think we can get just as good result _with_ clipping of transparent surfaces as without. Yes, transparent surfaces can be clipped! (...) (25 years ago, 1-Apr-00, to lugnet.cad.dev)
|
|
| | Re: BFC: LITS 2
|
|
Fifth and final in the series. Summary of the recap. This concludes my review of the "Line in the Sand" thread. If I have overlooked any issues, important or trivial, feel free to point them out. If there's something I didn't mention in this thread, (...) (25 years ago, 31-Mar-00, to lugnet.cad.dev)
|
|
| | Re: BFC: LITS 2
|
|
Fourth in the series, starting with message #41 in the "Line in the Sand" thread. Notice that I scanned past a number of messages before I got another 'open issue' hit. This posting covers up to & through message #83, the end of the thread. In (...) (25 years ago, 31-Mar-00, to lugnet.cad.dev)
|
|
| | Re: BFC: LITS 2
|
|
Here's the third message in my review of the "Line in the Sand" thread. This message covers my review from message #28 to message #40 in the thread (sorted by thread-view, not chronology). That's (URL) for the start, and (URL) for the finish. (...) (...) (25 years ago, 31-Mar-00, to lugnet.cad.dev)
|
|
| | Re: BFC: LITS 2
|
|
Second in a series, collect them all... (...) I believe the language around the 'defaults' has been cleared up sufficiently. (...) Hmm. I don't think there was much more discussion about whether every file should have an explicit 0 BFC CCW CLIP (...) (25 years ago, 31-Mar-00, to lugnet.cad.dev)
|
|
| | Re: open source & inventory ?
|
|
(...) ldlite is open source. Ldlite is a viewer for ldraw .dat files. (...) There is a way to do what you want, if you have dat files of a lego set, using steve blisses ldraw addon. (...) (25 years ago, 31-Mar-00, to lugnet.cad.dev)
|
|
| | open source & inventory ?
|
|
Hello, I've just resently discovered Ldraw and Mlcad and I'm absolutely amazed at the power of these programs, allthough I've not yet build a real model (other than the tutorial). I have got 2 questions however. 1) Are any of the programs open (...) (25 years ago, 31-Mar-00, to lugnet.cad.dev)
|