 | | Re: LPub and Lsynth page for tracking enhancement requests and bug fixes
|
|
"Kevin L. Clague" <kevin_clague@yahoo.com> wrote in message news:I52p4z.1xwI@lugnet.com... [ ... snipped ... ] (...) construction (...) sizes (...) LPub (...) I believe that will do. Thanks, Mike (20 years ago, 7-Oct-04, to lugnet.cad.dev)
|
| |
| | Re: LPub mask generation
|
|
"Kevin L. Clague" <kevin_clague@yahoo.com> wrote in message news:I52sF2.LI3@lugnet.com... (...) [ ... snipped ... ] (...) Excellent. I had been meaning to get the data back to you but have yet to do so. Let me know if I can provide anything else. (...) (20 years ago, 7-Oct-04, to lugnet.cad.dev)
|
| |
| | LDraw.org Downtime
|
|
Per the following post: (URL) will be down 10/5 at 2pm EDT for about 15 min. Since Peeron also hosts LDraw.org, LDraw.org will be down as well. -Orion (20 years ago, 4-Oct-04, to lugnet.cad, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LPub mask generation
|
|
(...) Mike, I recovered your emails about this problem and chasing it down. (...) Kevin (20 years ago, 4-Oct-04, to lugnet.cad.dev)
|
| |
| | Re: LPub and Lsynth page for tracking enhancement requests and bug fixes
|
|
(...) Looking at the above list seriously..... You list a number of sub-model specific desires including: 1. view angle on a sub-model basis. You already have this using MLCad's ROTSTEP meta-command. ROTSTEP only applies to the file that contains (...) (20 years ago, 4-Oct-04, to lugnet.cad.dev)
|
| |
| | Re: LPub request
|
|
(...) The PLIST BEGIN SUB meta solution is fine. My problem was due to a lack of knowledge regarding LPub META commands. -Orion (20 years ago, 4-Oct-04, to lugnet.cad.dev)
|
| |
| | Re: LPub and Lsynth page for tracking enhancement requests and bug fixes
|
|
(...) My solution to the above is to give you explicit control over construction image render window size and PLI render window size. You can set these sizes small for test runs. Is this acceptable? It will be available in the next LPub release. (...) (20 years ago, 4-Oct-04, to lugnet.cad.dev)
|
| |
| | Re: LPub request
|
|
(...) I'm adding support for s and 48 in lieu of the pathing solution Lars' will be providing. If your flexible axle is produced by some known tool, I'm willing to add supprt for flex axle recognition to LPub. Orion, could you email an example? (...) (20 years ago, 4-Oct-04, to lugnet.cad.dev)
|
| |
| | Re: LPub request
|
|
(...) Hi Orion, I never got feedback from you about the PLIST BEGIN SUB solution outlined above. LPub recognizes parts synthesized with LSynth and tries to determine the part being synthesized. It recognizes flexible axles and determines the length. (...) (20 years ago, 4-Oct-04, to lugnet.cad.dev)
|
| |
| | Re: New style of part file 3941 vs. 6143
|
|
(...) I've added pictures of some of these variants to my comparison galleries: (URL) the two previous pictures. One addition to Chris' excellent descriptions is that the older bottoms (2A) can be used in a SNOT function with plates; the newer (...) (20 years ago, 28-Sep-04, to lugnet.cad.dev.org.ldraw)
|
