 | | Re: Stud5 and type 5 lines at edge of cylinders.
|
|
(...) I don't think the S curve problem goes away. The tangent control point works perfectly for two (same radius) curves that both curl in the same direction. It also works perfectly for a curve joining a flat edge along the tangent. However it (...) (21 years ago, 17-Aug-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Stud5 and type 5 lines at edge of cylinders.
|
|
(...) Is there a reason that the cylinder primitives haven't been updated to work like the sphere primitive? As long as there are type 5 lines on both ends of each partial cylinder, and the control point out in space is tangent to the cylinder (...) (21 years ago, 17-Aug-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Stud5 and type 5 lines at edge of cylinders.
|
|
(...) So the problem could be solved by using high res primitives? I'll have to try that out. (21 years ago, 16-Aug-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Stud5 and type 5 lines at edge of cylinders.
|
|
(...) Ahh, the dreaded S-curve cylinder join rears it's ugly head again. I voted to ignore this a while back and gave my reasons. (URL) disagreed at the time. Don (21 years ago, 15-Aug-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Stud5 and type 5 lines at edge of cylinders. [DAT]
|
|
I recently reworked the stud 5 primitive to make use of more quarter cylinders. I then noticed that when viewed there were edge lines apearing where they shouldn't. If you look at the primitive from various points you can see this occur. 0 Stud (...) (21 years ago, 15-Aug-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Torus Primitives on the Part Tracker
|
|
(...) Cool! (...) More cool! (...) the two related part files, neither of which is certified, I'd say go ahead and update t04q3333.dat. (...) Certainly. Steve (21 years ago, 6-Jul-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Torus Primitives on the Part Tracker
|
|
Hello, I have been updating some of the torus primitve files to use quads, and conditional lines instead of cylinder primitves. I have had too many problems getting the cylinder files to show without gaps. I have a new tool that can generate any (...) (21 years ago, 4-Jul-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Primitive part file reviewing on the Parts Tracker
|
|
Hello all parts authors, Here is a note to say that I have been studying Primitives in detail lately. I will be making some changes on the primitive reviews I have made recently. So some parts will probably come off the certified list until the (...) (21 years ago, 10-Jun-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Peghole BFC?
|
|
(...) I'm not sure about using stud4 on the bottom of Brick 1x1 Round - it would somewhat odd when rendered in 'stud as line' mode; the bottom portion of the brick would be missing. (...) Your expectation is correct. The 'inside' surface of (...) (21 years ago, 22-May-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Peghole BFC?
|
|
Hi all, While going through some of James' original parts, correcting for BFC (and occasionally making appropriate changes, since these came before the ring primitives), I noticed that he used the peghole DAT for making bottom studs (see the Brick 1 (...) (21 years ago, 21-May-03, to lugnet.cad.dat.parts.primitives)
|
