Subject:
|
Re: [PART] 2717 Technic Seat (at last!)
|
Newsgroups:
|
lugnet.cad.dat.parts
|
Date:
|
Tue, 1 Feb 2000 21:07:23 GMT
|
Viewed:
|
1461 times
|
| |
|
|
Nice job! I think it's missing a couple edgelines. Let's see if I can
describe the area: looking at the part from the back in oblique view, the
sloping back of the seat meets the vertical back of the part, but the sides
of the seat back continue to slope down almost to the bottom of the part. At
the very lowest portion of this sloping surface, you used a 1-4disc. I think
it needs an edgeline where the 1-4disc meets the body of the part, and
perhaps also where it meets the sloping surface, since the 1-4 disc seems to
be vertical. If you look at the part in wireframe mode (oblique view),
you'll notice an edge which doesn't connect to anything--which is the only
reason I noticed this.
Also, I don't get a conditional line showing up at the front of the armrest
when the part is viewed from the back obliquely.
-John Van
Tore Eriksson <tore.eriksson@mbox325.swipnet.se> wrote in message
news:3890C876.5F54662E@mbox325.swipnet.se...
> 0 Technic Seat
> 0 Name: 2717.dat
> 0 Author: Tore Eriksson
> 0 Un-Official Part
>
>
|
|
Message has 2 Replies:
 | | Re: [PART] 2717 Technic Seat (at last!)
|
| (...) Thanks! :o) (...) Yes, the 1-4disc is vertical. If I remeber correctly, the Z/Y propotions should be 1/4. I'll have a look at it, as well as the missing lines you say that you've found.. (...) Yes, I'm aware of that. I thought of them some (...) (25 years ago, 1-Feb-00, to lugnet.cad.dat.parts)
| | | [PART] 2717 Technic Seat (ver 2) [DAT]
|
| (...) That's a new method to carefully reveiw a new part. Thanks! Hopefully, the flaws are corrected now. /Tore 0 Technic Seat 0 Name: 2717.dat 0 Author: Tore Eriksson 0 Un-Official Part 1 16 0 -4 10 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 0 -4 -10 1 0 0 (...) (25 years ago, 1-Feb-00, to lugnet.cad.dat.parts)
|
Message is in Reply To:
| | [PART] 2717 Technic Seat (at last!) [DAT]
|
| 0 Technic Seat 0 Name: 2717.dat 0 Author: Tore Eriksson 0 Un-Official Part 1 16 0 -4 10 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 0 -4 -10 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 0 0 0 16 0 0 0 -4 0 0 0 26 box5.dat 2 24 -20 0 -30 20 0 -30 2 24 -20 0 30 20 0 30 2 (...) (25 years ago, 27-Jan-00, to lugnet.cad.dat.parts)
|
5 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
