 | | 6246f: Minifig Oilcan —John VanZwieten
|
| | | This completes the 6246 ring of minifig tools. I'd like input on where to center this. My preference would be to center on the handle, with the whole thing tilted so that the handle fits upright in a minifig hand. This would be different than the (...) (25 years ago, 13-Jul-99, to lugnet.cad.dat.parts)
|
| | | |
| | | | | Re: 6246f: Minifig Oilcan —Jonathan Wilson
|
| | | | | thanks. i notice that you are trying to ldraw every part needed for the x-wing you possibly can... keep up the good work. now, asside from the minifig parts all we need is the death star slope. (25 years ago, 13-Jul-99, to lugnet.cad.dat.parts)
|
| | | | | |
| | | | | | | Re: 6246f: Minifig Oilcan —John VanZwieten
|
| | | | | | Jonathan Wilson <wilsonj@xoommail.com> wrote in message news:378BCAD2.9B03F6...ail.com... (...) x-wing you possibly can... keep up the good work. now, asside from the minifig parts all we need is the death star slope. Yup. I've actually begun work (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| | | | | | |
| | | | | | | | Re: 6246f: Minifig Oilcan —Jonathan Wilson
|
| | | | | | i do not have the slope so i cant do it. (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| | | | | | |
| | | | | | | | Re: 6246f: Minifig Oilcan —Jonathan Wilson
|
| | | | | | about the next thing to work on... could you mabie do 7150 before the snowspeeder? especially the imperial logo and mailbox door? (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| | | | | | |
| | | | | Re: 6246f: Minifig Oilcan —Fredrik Glöckner
|
| | | | | (...) This sounds like a good idea to me too. Centering it on the handle makes it easy to use in most cases, as I assume most will have it either attached to a minifig hand or to one of those 1x1 plates with clip, say. Too bad that the power drill (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| | | | | |
| | | | | Re: 6246f: Minifig Oilcan —Steve Bliss
|
| | | | | [followups set to lugnet.cad.dev] Nice job! Now I don't have to worry about that entry on the Parts Tracker anymore. :) The power drill could be modified. I doubt it's seen much use. Especially not in situations where the position is (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| | | | | |
| | | | | | | Re: 6246f: Minifig Oilcan —John VanZwieten
|
| | | | | | Steve Bliss <blisses@worldnet.att.net> wrote in message news:378c87c0.798940...net.com... (...) I almost contacted you to see if you had done anything on it, but I figured that since you would have been working on it before the cone primitives came (...) (25 years ago, 14-Jul-99, to lugnet.cad.dev)
|
| | | | | | |
| | | | | | | | Re: 6246f: Minifig Oilcan —Steve Bliss
|
| | | | | | (...) OK. I will do it. (...) I'm not keen on those specific names, but I'm OK with the idea of one-word categories. Do we need to stick with the idea of 'category = first word in title', or can we move on at this point? I think the only programs (...) (25 years ago, 14-Jul-99, to lugnet.cad.dev)
|
| | | | | | |
| | | | | | | | Re: 6246f: Minifig Oilcan —John VanZwieten
|
| | | | | | (...) Maybe just MinifigTool, MinifigAccessory, MinifigWeapon? (...) That's the rub. If there were a makelist which sorted on category, then we could use more logical partnames, and put our goofy category/sorting language in a 0 Category statement. (...) (25 years ago, 15-Jul-99, to lugnet.cad.dev)
|
| | | | | | |
| | | | | Recentered 6246f: Minifig Oilcan —John VanZwieten
|
| | | | This is how I will submit this part: 0 Minifig Oilcan 0 Name: 6246f.dat 0 Author: John VanZwieten 0 Un-Official Element 0 12.529 Degrees rotation on x-axis to make bottom of can level 1 16 0 14.471 -21.259 8 0 0 0 0.976 1.736 0 -0.217 7.808 (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| | | | |
