Special:
|
[DAT] (requires LDraw-compatible viewer)
|
Subject:
|
Re: Part Requests
|
Newsgroups:
|
lugnet.cad.dat.parts
|
Date:
|
Tue, 2 Jan 2001 18:03:18 GMT
|
Viewed:
|
923 times
|
| |
|
|
In lugnet.cad.dat.parts, Mladen Pejic writes:
> I was wondering if anybody here is planning or in the process of making these
> parts:
>
> 30565 (4 x 4 curved plate)
> 30562 (4 x 4 x 6 curved hollow cylinder)
And here's a mockup for the panel.
I'm starting to dislike the "Cylinder" category. First, the name is too
specific; there's an implied exclusion of cones, domes, etc. A general
"Round" category would be better. The second problem with "Cylinder" is
that almost everything in the category could also belong in some other
category, such as "Brick" or "Panel".
Argh.
--
Steve
0 Panel 4 x 4 x 6 Quarter Round
0 Name: 30562.DAT
0 Author: Steve Bliss
0 Unofficial Element
0 CATEGORY Panel
0 KEYWORDS quarter cylinder, wall, corner round
0 BFC CERTIFY CW
0 Outline - top curves
1 16 0 0 0 0 0 80 0 1 0 -80 0 0 48\1-4edge.dat
1 16 0 0 0 0 0 60 0 1 0 -60 0 0 48\1-4edge.dat
1 16 0 4 0 0 0 60 0 1 0 -60 0 0 48\1-4edge.dat
1 16 0 4 0 0 0 76 0 1 0 -76 0 0 48\1-4edge.dat
0 - Z=0 side
2 24 60 0 0 80 0 0
2 24 80 0 0 80 144 0
2 24 80 144 0 60 144 0
2 24 60 144 0 60 136 0
2 24 60 136 0 76 136 0
2 24 76 136 0 76 4 0
2 24 76 4 0 60 4 0
2 24 60 4 0 60 0 0
0 - X=0 side
2 24 0 0 -60 0 0 -80
2 24 0 0 -80 0 144 -80
2 24 0 144 -80 0 144 -60
2 24 0 144 -60 0 136 -60
2 24 0 136 -60 0 136 -76
2 24 0 136 -76 0 4 -76
2 24 0 4 -76 0 4 -60
2 24 0 4 -60 0 0 -60
0 - bottom curves
1 16 0 144 0 0 0 80 0 1 0 -80 0 0 48\1-4edge.dat
1 16 0 144 0 0 0 60 0 1 0 -60 0 0 48\1-4edge.dat
1 16 0 136 0 0 0 60 0 1 0 -60 0 0 48\1-4edge.dat
1 16 0 136 0 0 0 76 0 1 0 -76 0 0 48\1-4edge.dat
0 cylinder walls
1 16 0 0 0 0 0 80 0 144 0 -80 0 0 48\1-4cyli.dat
0 BFC INVERTNEXT
1 16 0 0 0 0 0 60 0 4 0 -60 0 0 48\1-4cyli.dat
0 BFC INVERTNEXT
1 16 0 4 0 0 0 76 0 132 0 -76 0 0 48\1-4cyli.dat
0 BFC INVERTNEXT
1 16 0 136 0 0 0 60 0 8 0 -60 0 0 48\1-4cyli.dat
0 horizontal surfaces
1 16 0 0 0 0 0 20 0 1 0 -20 0 0 48\1-4ring3.dat
1 16 0 4 0 0 0 20 0 -1 0 -20 0 0 48\1-4ring3.dat
1 16 0 136 0 0 0 20 0 1 0 -20 0 0 48\1-4ring3.dat
0 straight vertical surfaces
4 16 0 136 -76 0 144 -80 0 144 -60 0 136 -60
4 16 0 4 -76 0 0 -80 0 144 -80 0 136 -76
4 16 0 4 -60 0 0 -60 0 0 -80 0 4 -76
4 16 60 144 0 80 144 0 76 136 0 60 136 0
4 16 80 144 0 80 0 0 76 4 0 76 136 0
4 16 80 0 0 60 0 0 60 4 0 76 4 0
1 16 70 0 -10 1 0 0 0 1 0 0 0 1 stud2.dat
1 16 50 0 -50 1 0 0 0 1 0 0 0 1 stud2.dat
1 16 10 0 -70 1 0 0 0 1 0 0 0 1 stud2.dat
0
|
|
Message has 2 Replies:
 | | Re: Part Requests
|
| WOW! Thanks a lot Steve. I also agree with you about the cylinder category. When I sort my LEGO, I have sort all the round plates and round bricks into one section. (...) (24 years ago, 2-Jan-01, to lugnet.cad.dat.parts)
|
Message is in Reply To:
| | Part Requests
|
| I was wondering if anybody here is planning or in the process of making these parts: 30565 (4 x 4 curved plate) 30562 (4 x 4 x 6 curved hollow cylinder) Both of these parts are from the new Star Wars LEGO set 7106 Droid Escape ((URL) I really need (...) (24 years ago, 30-Nov-00, to lugnet.cad.dat.parts)
|
6 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
