Subject:
|
Re: Part Requests
|
Newsgroups:
|
lugnet.cad.dat.parts
|
Date:
|
Tue, 2 Jan 2001 18:26:35 GMT
|
Viewed:
|
933 times
|
| |
|
|
WOW! Thanks a lot Steve. I also agree with you about the cylinder category.
When I sort my LEGO, I have sort all the round plates and round bricks into one
section.
Mladen Pejic, over and out!
http://members.attcanada.ca/~milovan/index.htm
In lugnet.cad.dat.parts, Steve Bliss writes:
> In lugnet.cad.dat.parts, Mladen Pejic writes:
> > I was wondering if anybody here is planning or in the process of making these
> > parts:
> >
> > 30565 (4 x 4 curved plate)
> > 30562 (4 x 4 x 6 curved hollow cylinder)
>
> And here's a mockup for the panel.
>
> I'm starting to dislike the "Cylinder" category. First, the name is too
> specific; there's an implied exclusion of cones, domes, etc. A general
> "Round" category would be better. The second problem with "Cylinder" is
> that almost everything in the category could also belong in some other
> category, such as "Brick" or "Panel".
>
> Argh.
>
> --
> Steve
>
>
> 0 Panel 4 x 4 x 6 Quarter Round
> 0 Name: 30562.DAT
> 0 Author: Steve Bliss
> 0 Unofficial Element
>
> 0 CATEGORY Panel
> 0 KEYWORDS quarter cylinder, wall, corner round
>
> 0 BFC CERTIFY CW
>
> 0 Outline - top curves
> 1 16 0 0 0 0 0 80 0 1 0 -80 0 0 48\1-4edge.dat
> 1 16 0 0 0 0 0 60 0 1 0 -60 0 0 48\1-4edge.dat
> 1 16 0 4 0 0 0 60 0 1 0 -60 0 0 48\1-4edge.dat
> 1 16 0 4 0 0 0 76 0 1 0 -76 0 0 48\1-4edge.dat
> 0 - Z=0 side
> 2 24 60 0 0 80 0 0
> 2 24 80 0 0 80 144 0
> 2 24 80 144 0 60 144 0
> 2 24 60 144 0 60 136 0
> 2 24 60 136 0 76 136 0
> 2 24 76 136 0 76 4 0
> 2 24 76 4 0 60 4 0
> 2 24 60 4 0 60 0 0
> 0 - X=0 side
> 2 24 0 0 -60 0 0 -80
> 2 24 0 0 -80 0 144 -80
> 2 24 0 144 -80 0 144 -60
> 2 24 0 144 -60 0 136 -60
> 2 24 0 136 -60 0 136 -76
> 2 24 0 136 -76 0 4 -76
> 2 24 0 4 -76 0 4 -60
> 2 24 0 4 -60 0 0 -60
> 0 - bottom curves
> 1 16 0 144 0 0 0 80 0 1 0 -80 0 0 48\1-4edge.dat
> 1 16 0 144 0 0 0 60 0 1 0 -60 0 0 48\1-4edge.dat
> 1 16 0 136 0 0 0 60 0 1 0 -60 0 0 48\1-4edge.dat
> 1 16 0 136 0 0 0 76 0 1 0 -76 0 0 48\1-4edge.dat
>
> 0 cylinder walls
> 1 16 0 0 0 0 0 80 0 144 0 -80 0 0 48\1-4cyli.dat
> 0 BFC INVERTNEXT
> 1 16 0 0 0 0 0 60 0 4 0 -60 0 0 48\1-4cyli.dat
> 0 BFC INVERTNEXT
> 1 16 0 4 0 0 0 76 0 132 0 -76 0 0 48\1-4cyli.dat
> 0 BFC INVERTNEXT
> 1 16 0 136 0 0 0 60 0 8 0 -60 0 0 48\1-4cyli.dat
>
> 0 horizontal surfaces
> 1 16 0 0 0 0 0 20 0 1 0 -20 0 0 48\1-4ring3.dat
> 1 16 0 4 0 0 0 20 0 -1 0 -20 0 0 48\1-4ring3.dat
> 1 16 0 136 0 0 0 20 0 1 0 -20 0 0 48\1-4ring3.dat
>
> 0 straight vertical surfaces
> 4 16 0 136 -76 0 144 -80 0 144 -60 0 136 -60
> 4 16 0 4 -76 0 0 -80 0 144 -80 0 136 -76
> 4 16 0 4 -60 0 0 -60 0 0 -80 0 4 -76
>
> 4 16 60 144 0 80 144 0 76 136 0 60 136 0
> 4 16 80 144 0 80 0 0 76 4 0 76 136 0
> 4 16 80 0 0 60 0 0 60 4 0 76 4 0
>
> 1 16 70 0 -10 1 0 0 0 1 0 0 0 1 stud2.dat
> 1 16 50 0 -50 1 0 0 0 1 0 0 0 1 stud2.dat
> 1 16 10 0 -70 1 0 0 0 1 0 0 0 1 stud2.dat
>
> 0
|
|
Message is in Reply To:
 | | Re: Part Requests [DAT]
|
| (...) And here's a mockup for the panel. I'm starting to dislike the "Cylinder" category. First, the name is too specific; there's an implied exclusion of cones, domes, etc. A general "Round" category would be better. The second problem with (...) (24 years ago, 2-Jan-01, to lugnet.cad.dat.parts)
|
6 Messages in This Thread:
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
