To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.cad.dat.partsOpen lugnet.cad.dat.parts in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 CAD / LDraw Files / Parts / 1935
1934  |  1936
Subject: 
Re: New Part whole 6002 (needs work)
Newsgroups: 
lugnet.cad.dat.parts
Date: 
Sat, 25 Nov 2000 01:43:42 GMT
Viewed: 
834 times
  
Oh Yeah!

I've been waiting forever for this part!  I love to use the straight
version.

I checked out your part.  It looks really good.  My only possible complaint
is that the 1x2 straight portion at the very bottom (that would accept 2
studs in a row) looks too "clear" in POV-RAY when I make it
trans-light-gray.  I can even see this on MLCAD.  Unfortunately, I am not
enough of a parts expert to know what might be missing (or if I am just
noticing some artifact and the part is actually fine).  Anyhow, even with
this, it is plenty good enough to use.  I plan to put it to work right away!

By the way, the sub-part for this also shows up in my MLCAD parts selection
area.  Is there some way to make it so I can use this sub-part as part of
the main part, but so it doesn't show up in MLCAD?

thanks


Mark Kennedy <kennedy@proaxis.com> wrote in message
news:G4Exq4.w7@lugnet.com...
And here is the main part that uses the previous subfile. Please let me • know
what you think!


0 part 6002 round Panel  6 x  6 x  9 with Spherous Top
0 by Mark Kennedy
0 based on 2572 by unknown author
1 16 0 0 0 1 0 0 0 1 0 0 0 1 6002s2.DAT
1 16 0 0 0 0 0 1 0 1 0 1 0 0 6002s2.DAT
1 16 -10 0 -10 -1 0 0 0 1 0 0 0 -1 stud.dat
1 16 10 0 10 -1 0 0 0 1 0 0 0 -1 stud.dat
1 16 20 212 20 0 0 20 0 1 0 20 0 0 1-4ring3.dat
1 16 20 208 20 0 0 20 0 1 0 20 0 0 1-4ring3.dat
1 16 20 208 20 60 0 0 0 0 0 0 0 60 1-4edge.dat
1 16 20 80 20 80 0 0 0 128 0 0 0 80 1-4cyli.dat
1 16 20 80 20 76 0 0 0 128 0 0 0 76 1-4cyli.dat
1 16 20 80 20 80 0 0 0 -80 0 0 0 80 1-8sphe.dat
1 16 20 80 20 76 0 0 0 -76 0 0 0 76 1-8sphe.dat
0



Message has 1 Reply:
  Re: New Part whole 6002 (needs work)
 
(...) Oops, I'll have to fix that... (...) You could possibly move the half part to /S subdirectory in parts. That may help (24 years ago, 25-Nov-00, to lugnet.cad.dat.parts)

Message is in Reply To:
  New Part whole 6002 (needs work)  [DAT]
 
And here is the main part that uses the previous subfile. Please let me know what you think! 0 part 6002 round Panel 6 x 6 x 9 with Spherous Top 0 by Mark Kennedy 0 based on 2572 by unknown author 1 16 0 0 0 1 0 0 0 1 0 0 0 1 6002s2.DAT 1 16 0 0 0 0 (...) (24 years ago, 22-Nov-00, to lugnet.cad.dat.parts)

5 Messages in This Thread:


Entire Thread on One Page:
Nested:  All | Brief | Compact | Dots
Linear:  All | Brief | Compact

This Message and its Replies on One Page:
Nested:  All | Brief | Compact | Dots
Linear:  All | Brief | Compact
    

Custom Search

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR