 | | Re: Naming of parts
|
|
"Niels Karsdorp" <nkp.nkp@hetnet.nl> schreef in bericht news:HsIEAw.1sur@lugnet.com... (...) for (...) I totally agree with Niels here (again :-) There should be a better way for naming parts. Jaco (21 years ago, 3-Feb-04, to lugnet.cad.dat.parts)
|
| |
| | Naming of parts
|
|
I think more parts need to be renamed. Recently I was looking for the large excavator arm, did not find it among the parts starting with an E (like the small 3314 Excavator Arm 2 x 6 x 2), did not find it on the PT searching for 'Excavator', so I (...) (21 years ago, 3-Feb-04, to lugnet.cad.dat.parts)
|
| |
| | Re: Dishes are Round (Cornbread are Square)
|
|
(...) 1. Will they still be considered part of the Round category? (I.e., will they then need a "0 CATEGORY Round" meta-statement?) 2. Won't they need "Space", "radar", and "round" added to their lists of KEYWORDS? Thnx, Franklin (21 years ago, 3-Feb-04, to lugnet.cad.dat.parts)
|
| |
| | Re: Dish 2 x 2 (4740.dat)
|
|
(...) After some offline discussion with Steve Bliss we have decided that the dish parts will all be named "Dish ...". I'll be fixing the names of the parts on the PT and searching out any that remain to be fixed on the official library. Chris (21 years ago, 2-Feb-04, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3035p01.dat - confirmation, it exists!
|
|
(...) Thanks Clark! Too bad that geocities.jp link is dead. That would have been so much easier to tell if the part had been red... Well, I think it is ABS. No sign of misforming, I'd say the stud logo is late 60's, higher and more modern than the (...) (21 years ago, 1-Feb-04, to lugnet.cad.dat.parts)
|
| |
| | Re: File Size Concerns ( Was Re: Animal Tail Section end (NEW))
|
|
(...) I agree. If I would reduce the decimal points the size would be reduced by 20k but then I get a lot of not coplanar vertices so that these needs to be split (increeses size) or have to store with the numbers. But the neighbour vertices needed (...) (21 years ago, 1-Feb-04, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 3035p01.dat - confirmation, it exists!
|
|
(...) Yes it does exist. It was factory painted to match the wing. It's from set 310. I have a picture of that set MIB showing both parts with red edge paint. Gary Istok also mentions it: (URL) to me is the years Gary mentioned. The plate you (...) (21 years ago, 1-Feb-04, to lugnet.cad.dat.parts)
|
| |
| | New Part: 3036p01.dat - Plate 6 x 8 with Red Side [DAT]
|
|
Must be from set 310. (URL) Plate 6 x 8 with Red Side 0 Name: 3036p01.dat 0 Author: Tore Eriksson 0 Author: James Jessiman (Original LDraw Part) 0 BFC CERTIFY CW 1 16 60 4 40 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 40 4 40 1 0 0 0 -1 0 0 0 1 stud4.dat 1 (...) (21 years ago, 1-Feb-04, to lugnet.cad.dat.parts)
|
| |
| | New Part: 3035p01.dat - Please confirm that it exists! [DAT]
|
|
Could be somebody painted the red side to fit in with the rounded "wing" from some gas station set? But I think it's real. 0 Plate 4 x 8 with Red Side 0 Name: 3035p01.dat 0 Author: Tore Eriksson 0 Author: James Jessiman (Original LDraw Part) 0 BFC (...) (21 years ago, 1-Feb-04, to lugnet.cad.dat.parts)
|
| |
| | Re: File Size Concerns ( Was Re: Animal Tail Section end (NEW))
|
|
(snip) I think you're both right. I am reminded of a quote: "Make things as simple as possible, but not simpler." -Albert Einstein You're both geniuses too, you know. :-) (21 years ago, 1-Feb-04, to lugnet.cad.dat.parts)
|
