| | Question about a new kind of stud [DAT]
|
|
Hi, I'm modelling the following part: (URL) "Door 1 x 4 x 6 Frame", but this part has a different kind of stud: (URL) I didn't find this stud in the primitives directory, so, I start modelling it. Also, I didn't find a ring compatible with the (...) (23 years ago, 18-Mar-02, to lugnet.cad.dat.parts.primitives)
|
|
| | Re: 2618.dat Auqanaut Bubble Base (Updated)
|
|
I have another problem with this part, beside the strange rotation angle: The hollow studs at the upper rim should stick out, just as much as normal studs, but they don't. Or is it just me ..? (23 years ago, 18-Mar-02, to lugnet.cad.dat.parts)
|
|
| | Re: 2618.dat Auqanaut Bubble Base (Updated)
|
|
Orion, Can you rotate the part 90 degrees around the X axis? The current orientation is ... unprecedented. :) Steve (...) [snip] (23 years ago, 18-Mar-02, to lugnet.cad.dat.parts)
|
|
| | Re: New Part - Brick 2 x 2 Round with Buttons Pattern
|
|
(...) That looks very good to me - well done. Another part I can remove from my box of "I'll get around to authoring that sometime" parts. Chris (23 years ago, 18-Mar-02, to lugnet.cad.dat.parts)
|
|
| | New Part: x744.dat - Technic Gear 42 Tooth [DAT]
|
|
0 Technic Gear 42 Tooth 0 Name: x744.dat 0 Author: Tore Eriksson 0 Unofficial Element 0 CATEGORY Technic 0 KEYWORDS gear, pre-technic, Samsonite 0 CMDLINE -c4 0 Samsonite is registered trademark of Samsonite, Inc 1 16 9 0 0 0 0 0 8 0 0 0 0 8 (...) (23 years ago, 18-Mar-02, to lugnet.cad.dat.parts)
|
|
| | New Part - Brick 2 x 2 Round with Buttons Pattern [DAT]
|
|
I found it in Set No 6394 - Service Station CU Bernd 0 Brick 2 x 2 Round with Buttons Pattern 0 Name: 3941p01.dat 0 Author: Bernd Broich 0 Unofficial part 0 Original Part 1 16 -10 0 -10 1 0 0 0 1 0 0 0 1 stud.dat 1 16 -10 0 10 1 0 0 0 1 0 0 0 1 (...) (23 years ago, 18-Mar-02, to lugnet.cad.dat.parts)
|
|
| | 2618.dat Auqanaut Bubble Base (Updated) [DAT]
|
|
Thanks to Carston for his helpful post. For some reason LDDesignPad didn't list any errors. I had to run L3P in DOS mode. Anyway, here's the updated DAT, L3P error free. -Orion 0 Aquanaut Bubble Base 0 Name: 2618.ldr 0 Author: Orion Pobursky 0 (...) (23 years ago, 17-Mar-02, to lugnet.cad.dat.parts)
|
|
| | Re: 2618.dat Auqanaut Bubble Base (Final, I Hope)
|
|
Hello Orion! (...) As (...) Amazing part! I don't know if this is your first part but it looks very good and i bet it was some hard work! Two things i noticed. - Some missing lines at the egdes of the four half-button prints (bottom of part) - Check (...) (23 years ago, 17-Mar-02, to lugnet.cad.dat.parts)
|
|
| | 2618.dat Auqanaut Bubble Base (Final, I Hope) [DAT]
|
|
After 2 weeks of tweaking I think I am finally ready to release my part. As this is my first part, please let me know if I made any part authoring no-no's or if you have any improvements to suggest. Thanks -Orion Pobursky 0 Aquanaut Bubble Base 0 (...) (23 years ago, 17-Mar-02, to lugnet.cad.dat.parts)
|
|
| | Re: 2x4 left and right half wedge brick and plate
|
|
(...) Actually, I need an *income* (i.e., a job) first. :-/ *Then* I can start acquiring more new LEGO. >:-D (...) I haven't found a dirt-cheap (under $10) set with those parts at a local store, yet. :-/ Thanks, Franklin (23 years ago, 16-Mar-02, to lugnet.cad.dat.parts)
|