 | | Re: Updated Part 30117
|
|
(...) Hello, I looked at the picture mentioned above, looked at the part with L3lab, LDview and l3glite~3.7.?, couldn't see the missing pieces, you are indicating. Otherwise the part looks great! Even the studs are correctly oriented. (yes, I check (...) (23 years ago, 13-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Updated Part 30117
|
|
(...) I don't have the part with me, so I'm not positive about this, but... If you look at the underside of the part you seem to be missing two triangles, one on the left and one on the right. You can see inside the bottom part of those three steps. (...) (23 years ago, 12-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | 30504 plate 8x8 sans corner [DAT]
|
|
And here is the complete piece. 0 Plate 8 x 8 without Corner 0 Name: 30504.dat 0 Author: Mark Kennedy 0 1 16 -60 4 60 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 -40 4 40 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 -20 4 20 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 0 4 0 1 0 0 (...) (23 years ago, 12-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | 30504s2 plate 8 by 8 sans corner: halfpart [DAT]
|
|
and now here is the half part using that new subpart thingy. 0 Plate 8 x 8 without Corner 0 Name: 30504.dat 0 Author: Mark Kennedy 0 1 16 -60 4 -60 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 -60 4 -40 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 -60 4 -20 1 0 0 0 -1 0 (...) (23 years ago, 12-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Updated Part 30117 [DAT]
|
|
Hi all, I have updated my 30117.dat. Paul showed me some bugs. This is the complete new part in orientation of Steves file of this part, posted some times ago. PLMKWYT / CU Bernd 0 Panel 10 x 10 x 2 1/3 Quarter Saucer Top 0 Name: 30117.DAT 0 Author: (...) (23 years ago, 11-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part : 3314.dat - Excavator Arm 2 x 6 x 2
|
|
(...) No - these were authored from scratch. Like Jason, I was amazed (or even embarressed) that they didn't exist. (...) No - I need to have the part, the time and motivation. This was just a good week - some days the visualisation comes easier (...) (23 years ago, 12-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part : 3314.dat - Excavator Arm 2 x 6 x 2
|
|
(...) Someone just requested the bucket and its arm. You are so quick. I can't believe it's true. Do you retain your unofficial parts until demand ? Are you the lamp's genie that can satisfy any part ? Or do you satisfy only 3 parts and then (...) (23 years ago, 11-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Subpart thingy. [DAT]
|
|
Here is a new subpart I made for use on all those corner plates. Also I am working on a plate 8X8 with corner missing number 30504 available in the Harry Potter sorting hat. 0 1 16 1.50 4 -1.50 6 0 -1.50 0 4 0 6 0 1.50 box4-1.dat 1 16 -1.50 4 1.50 1 (...) (23 years ago, 11-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | New Part : 3314.dat - Excavator Arm 2 x 6 x 2 [DAT]
|
|
Here is the small excavator arm - I kept the same orientation as 828, but set the origin to match the bucket. All comments welcome. Chris 0 Excavator Arm 2 x 6 x 2 0 Name: 3314.dat 0 Author: Chris Dee (chris_w_dee@hotmail.com) 0 Unofficial part 1 16 (...) (23 years ago, 10-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | New Part : x784.dat - Excavator Bucket 2 x 4 [DAT]
|
|
Here is the small excavator bucket. I have kept the same orientation as 3433.dat, but made the origin at the pivot point. Please let me know what you think. Note that temporary number x784 was previously used for the exhaust pipe part, for which the (...) (23 years ago, 8-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | New Part: FabWhel2.dat - Fabuland Wheel without Stud [DAT]
|
|
File name will most likely be subject to change. 0 Fabuland Wheel without Stud 0 Author: Tore Eriksson 0 Name: FabWhel2.dat 0 Unofficial Part 1 16 0 0 0 0 0 0 24 0 0 0 0 24 4-4edge.dat 1 16 0 0 0 0 0 0 20 0 0 0 0 20 4-4edge.dat 1 16 10 0 0 0 0 0 20 (...) (23 years ago, 8-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | New Part: FabWhel1.dat - Fabuland Wheel with Stud [DAT]
|
|
File name will most likely be subject to change. 0 Fabuland Wheel with Stud 0 Author: Tore Eriksson 0 Name: FabWhel1.dat 0 Unofficial Part 1 16 0 0 0 0 0 0 24 0 0 0 0 24 4-4edge.dat 1 16 0 0 0 0 0 0 20 0 0 0 0 20 4-4edge.dat 1 16 10 0 0 0 0 0 20 0 0 (...) (23 years ago, 8-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 4796.dat - Fabuland Car Chassis 8 x 6 [DAT]
|
|
(...) No, the explaination is found in my system to use the colour constants c, d, e, and f and assign them different colours in construction stage, and finally assign them colour 16. This time, I should have assigned f=CHROME but, like I'm used to, (...) (23 years ago, 7-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 4796.dat - Fabuland Car Chassis 8 x 6
|
|
(...) I don't have this part so I can't help you there. That may also explain why I don't know the answer to this question: Why aren't the axle end circles chrome like the bulk of the axle? (URL) the axle be a separate chrome subpart? Don PS. Some (...) (23 years ago, 7-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Tyre 28 x 70 (Technic low profile tyre)
|
|
(...) I didn't know that. I only use MLCad to create MPD files. Marc Klein A Mindstorms fan. (23 years ago, 6-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | New Part: 4796.dat - Fabuland Car Chassis 8 x 6 [DAT]
|
|
Found a couple of almost finished lds files. Now it's finished. Any idea of the part number for the 14 x 6 chassis? 0 Fabuland Car Chassis 8 x 6 0 Author: Tore Eriksson 0 Name: 4796.dat 0 Unofficial Part 0 f-s 2 24 18 8 -76 18 4 -56 2 24 -18 8 -76 (...) (23 years ago, 6-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Tyre 28 x 70 (Technic low profile tyre)
|
|
(...) That looks very good. Just a small note - the MPD file should have the s/ on the 0 FILE line for the subfile, viz 0 FILE s/32078a.dat 0 ~Tyre 28 x 70 subpart 0 Name: s/32078a.dat That way the file will open in L3Lab (and other DAT/MPD (...) (23 years ago, 6-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Tyre 28 x 70 (Technic low profile tyre) [DAT]
|
|
0 FILE 32078.dat 0 Tyre 28 x 70 0 Name: 32078.dat 0 Author: Marc Klein 0 Unofficial Part 1 16 0 0 0 0.866025 -0.5 0 0.5 0.866025 0 0 0 1 s/32078a.dat 1 16 0 0 0 1 0 0 0 1 0 0 0 1 s/32078a.dat 1 16 0 0 0 0.5 -0.866025 0 0.866025 0.5 0 0 0 1 (...) (23 years ago, 5-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New part: 30343 Window 4 x 10 x 2 Slope Double
|
|
(...) (note: despite the difference in dimensions, they are the same parts) (...) They were unofficial parts, posted to this newsgroup some time ago. As far as I can tell, Thomas never submitted them for official consideration. You might want to (...) (23 years ago, 4-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New part: 30343 Window 4 x 10 x 2 Slope Double
|
|
(...) Hmmmm. I just downloaded the complete 2000-02 parts, and they weren't in there. Has there been another update since then? Or did they come from somewhere else? Thanks ROSCO (23 years ago, 4-Oct-01, to lugnet.cad.dat.parts)
|
