 | | Re: Part number needed & New primitive submission
|
|
Hmm... Steve Bliss <blisses@worldnet.att.net> wrote in message news:379efb57.879462...net.com... (...) I'll do this, I guess it will save some time when being generated. (...) to (...) I don't know what YMMV stands for:) I'll check this out though. (...) (25 years ago, 28-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Re: Part number needed & New primitive submission
|
|
(...) center and (...) can (...) The way this primitive is designed saves time for the part author (not a whole lot, but some). Once you have the dimensions you want you just plug those in directly without having to divide them by two. When you use (...) (25 years ago, 28-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Re: Part number needed & New primitive submission
|
|
(...) I think the box should conform to the same geometry as the other box* primitives -- it should range from -1 to +1, not -.5 to +.5. Steve (25 years ago, 28-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Re: Part number needed & New primitive submission
|
|
A few things I noticed/suggestions: 1. The way you use box4nl, you are drawing a bunch of quads which will never be seen. Drop the end-quads from box4nl. 2. On the outside frame, butted-construction is not the best way to put graphics primitives (...) (25 years ago, 28-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Re: 4150p?? 4th try
|
|
It looks good. I would recommend two things. This is general advice, not something that must be changed on this part (although it would improve the pattern further): 1. When connecting quads/triangles/lines to primitives, use the same number of (...) (25 years ago, 28-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | 2431p?? (04?) [DAT]
|
|
Anyone able to confirm that it's p04? That's what it is on the part I'm looking at. 0 Tile 1 x 4 with Striped "RALLY" Pattern 0 Name: 2431p04.dat 0 Author: Patrick Sayre-Little 0 Unofficial Part 0 lines 4 0 -38 0 -8 36.5 0 -8 36.5 0 -8.5 -38 0 -8.5 (...) (25 years ago, 27-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Minifig Tool Fishing Rod 2614.dat [DAT]
|
|
Dear Part Creators, Hereby I submit the fishing rod part, that I have in Canadian mountains set. Please verify the part number, part name, category classification and the part itself before I send it to Terry. Thanks Ampi ---...--- Imre Papp (...) (25 years ago, 26-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Re: Part number needed & New primitive submission
|
|
(...) going (...) be (...) No, believe me I checked with my magnifying glass. No number. (...) and (...) and (...) Actually it is a swinging part like a door so the axis is through the rotational axis. The rotational axis on this part is just below (...) (25 years ago, 25-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Re: Tile 2 x 2 Corner Round Concave
|
|
pretend that the studs on the bottom of this part are not there. i left them there by mistake. (25 years ago, 25-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Re: Part number needed & New primitive submission
|
|
Never seen the part in question, but it looks ok. The new primitive seems ok, too. Very unusual that it starts from the center and goes from -0.5 to 0.5 in all directions. I don't know if I like it, but I can surely live with it. I like the name. nl (...) (25 years ago, 25-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
