 | | Re: 6246f: Minifig Oilcan
|
|
[followups set to lugnet.cad.dev] Nice job! Now I don't have to worry about that entry on the Parts Tracker anymore. :) The power drill could be modified. I doubt it's seen much use. Especially not in situations where the position is (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Re: My first part
|
|
(...) If there are two different patterns, then the ?? will be replaced with two different two-digit numbers. Just like we've always done. Steve (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | technic engine piston square 2x2 [DAT]
|
|
Hi, I'm not sure about the name, number and description and not about the lines in combination with the rounded edges. Any comments and or suggestions? Bart Titulaer 0 technic engine piston square 2x2 0 Name: pistonSQR.DAT 0 Author: Bart Titulaer 0 (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | tapbase also [DAT]
|
|
nothing changed, but I'm not sure wether it's already available on lugnet.com 0 Homemaker Tap Base 0 Name: tapbase.dat 0 Author: Tore Eriksson 0 Un-official Part 4 16 -20 0 -10 20 0 -10 16 0 -6 -16 0 -6 4 16 -20 0 10 20 0 10 16 0 6 -16 0 6 4 16 -20 (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | tap part number [DAT]
|
|
Hi, Jonathan send me yesterday this unofficial part, I've completed it. Tore Eriksson was and is the author (I should have asked you, but I saw it yesterday evening after I had finished it. I thought Jonathan was the original author), I think the (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Re: 6246f: Minifig Oilcan
|
|
(...) This sounds like a good idea to me too. Centering it on the handle makes it easy to use in most cases, as I assume most will have it either attached to a minifig hand or to one of those 1x1 plates with clip, say. Too bad that the power drill (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Re: My first part
|
|
(...) Thanks. You've saved me some potential frustration there. (...) What happens if there are two patterns with unknown official numbers? "4150p??" and "4150p???" ? (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Re: 6246f: Minifig Oilcan
|
|
thanks. i notice that you are trying to ldraw every part needed for the x-wing you possibly can... keep up the good work. now, asside from the minifig parts all we need is the death star slope. (25 years ago, 13-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | 6246f: Minifig Oilcan [DAT]
|
|
This completes the 6246 ring of minifig tools. I'd like input on where to center this. My preference would be to center on the handle, with the whole thing tilted so that the handle fits upright in a minifig hand. This would be different than the (...) (25 years ago, 13-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Re: My first part
|
|
(...) The problem is, you can't simply specify the background as a complete disk. You actually need to lay out the quads and triangles and primitives to build the background to fit around the foreground elements. In most 3D graphics systems (LDraw (...) (25 years ago, 13-Jul-99, to lugnet.cad.dat.parts)
|
