 | | Re: Working on Part 30384
|
|
Ok, I've made significant progress on this part (Thanks John! Thanks Steve!). In the process, I have made 3 "new" primitives (actually modifications of existing ones): 1-4con1 1-4ring3 1-4ring10 These were necessary to maintain the geometry, though (...) (25 years ago, 13-May-99, to lugnet.cad.dev, lugnet.cad.dat.parts)
|
| |
| | Re: Working on Part 30384
|
|
Ok, I've made significant progress on this part (Thanks John! Thanks Steve!). In the process, I have made 3 "new" primitives (actually modifications of existing ones): 1-4con1 1-4ring3 1-4ring10 These were necessary to maintain the geometry, though (...) (25 years ago, 13-May-99, to lugnet.cad.dev, lugnet.cad.dat.parts)
|
| |
| | Re: Working on Part 30384
|
|
Karim <knassar@mindspring.com> wrote in message news:37378F61.BEDC19...ing.com... (...) Nah. Too much trouble and it will make the piece look worse, not better. I'm going to leave it out on the X-Wing canopy as well. (...) I was considering doing (...) (25 years ago, 11-May-99, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Re: Working on Part 30384
|
|
windscreen canopy x by x by x??? i think that is the best place for it. (25 years ago, 11-May-99, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Working on Part 30384
|
|
I just started part 30384, the Naboo Fighter Canopy. I have a couple of questions: 1) There is a little divvet on the nose of the canopy. This seems to be a molding artifact, but it looks like it is a regular and prominent one. Should this be (...) (25 years ago, 11-May-99, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Re: looking for decorated slope piece
|
|
(...) I haven't seen that one done. Perhaps this is a good opportunity for you to learn part authoring. I think patterns are a great place for new authors to start. The tiger-stripe pattern would be a moderate challenge for you. -John Van (25 years ago, 9-May-99, to lugnet.cad.dat.parts, lugnet.cad)
|
| |
| | looking for decorated slope piece
|
|
Hi everyone, This is my first post to the cad group. I have checked the parts tracker page and several individuals pages and have not been able to find the piece I need to complete my LDRAW model. It is a 2x3 low slope from set#6180 "Sting Ray (...) (25 years ago, 8-May-99, to lugnet.cad.dat.parts, lugnet.cad)
|
| |
| | Unofficial Part: 30357 [DAT]
|
|
this is a repost from last week: --Karim ---...--- 0 Plate 3 x 3 Corner Round 0 Name: 30357.DAT 0 Author: Karim Nassar 0 Unofficial Element 0 Plate Top Edge 2 24 -10 0 -10 50 0 -10 2 24 -10 0 -10 -10 0 50 2 24 50 0 -10 50 0 10 2 24 -10 0 50 10 0 50 (...) (25 years ago, 6-May-99, to lugnet.cad.dat.parts)
|
| |
| | ------( Terms of use for lugnet.com )------
|
|
TERMS OF USE FOR LUGNET.COM OVERVIEW AND DEFINITIONS lugnet.com ("LUGNET") is a privately owned Internet site designed and run primarily for the benefit of those who enjoy building with, discussing, collecting, buying & selling, trading, and (...) (25 years ago, 4-May-99, to lugnet.cad.dat.parts.primitives)
|
| |
| | ------( Welcome to lugnet.cad.dat.parts.primitives )------
|
|
Welcome to lugnet.cad.dat.parts...rimitives, a LUGNET discussion group. CHARTER/PURPOSE: lugnet.cad.dat.parts.primitives (group): Parts primitives (special sub-elements upon which full elements are built) in LDraw DAT format, plus any follow-up (...) (25 years ago, 4-May-99, to lugnet.cad.dat.parts.primitives)
|
| |
| | ------( Terms of use for lugnet.com )------
|
|
TERMS OF USE FOR LUGNET.COM OVERVIEW AND DEFINITIONS lugnet.com ("LUGNET") is a privately owned Internet site designed and run primarily for the benefit of those who enjoy building with, discussing, collecting, buying & selling, trading, and (...) (25 years ago, 4-May-99, to lugnet.cad.dat.parts)
|
| |
| | ------( Welcome to lugnet.cad.dat.parts )------
|
|
Welcome to lugnet.cad.dat.parts, a LUGNET discussion group. CHARTER/PURPOSE: lugnet.cad.dat.parts (group): Unofficial renderings of official LEGO® elements/parts in LDraw DAT format, plus any follow-up discussions. lugnet.cad.dat (group and (...) (25 years ago, 4-May-99, to lugnet.cad.dat.parts)
|
