Subject:
|
Re: Realistic landing gear for x-wing
|
Newsgroups:
|
lugnet.cad.dat.ideas
|
Date:
|
Mon, 17 May 1999 17:39:49 GMT
|
Viewed:
|
2846 times
|
| |
|
|
My gear modifications are very close to yours, Bram. My rear gear is almost
exactly like yours, in fact, except I only used one cylinder brick on each
side, placed at the rear portion of the 1x2 tile. I used a similar concept
that you used on the front gear as well, except I removed the long 2x plate on
the bottom and broke it up a little to allow the ski to be more flush against
the bottom. I then reinforced the nose from the top and inside the storage
area. I didn't like the lightsaber migrating up into the nose where I had to
shake it out, so I closed off the ends of the storage area. That still leaves
enough room for the saber, too.
I've found the rear storage area to be a great place to put the extra parts
left over after building the various Star Wars sets, and now I have enough
stuff for Luke to make his little Dagobah camp setup. :-)
In lugnet.cad.dat.ideas, Bram Lambrecht writes:
> Here's the landing gear I added to my X-Wing. The studs on the rear
> landing gear should go in the middle of the engines, and I attached the
> front landing gear on the nose right before the body gets wider. (If
> only hull bricks were only 1 brick wide--then you could make the landing
> gear retract all the way into the nose.) As it is now, the landing gear
> is still mostly visible when retracted. Please LMKWYT.
> --Bram
>
> 0
> 1 7 50 0 -10 1 0 0 0 1 0 0 0 1 3794.DAT
> 1 7 -50 0 -10 1 0 0 0 1 0 0 0 1 3794.DAT
> 1 7 50 0 10 1 0 0 0 1 0 0 0 1 3794.DAT
> 1 7 -50 0 10 1 0 0 0 1 0 0 0 1 3794.DAT
> 1 7 40 8 0 0 0 -1 0 1 0 1 0 0 3938.DAT
> 1 7 -40 8 0 0 0 1 0 1 0 -1 0 0 3938.DAT
> 1 8 40 8 0 0 0 -1 0 1 0 1 0 0 3937.DAT
> 1 8 -40 8 0 0 0 1 0 1 0 -1 0 0 3937.DAT
> 1 7 40 32 -10 1 0 0 0 1 0 0 0 1 3062b.DAT
> 1 7 -40 32 -10 1 0 0 0 1 0 0 0 1 3062b.DAT
> 1 7 -40 32 10 1 0 0 0 1 0 0 0 1 3062b.DAT
> 1 7 40 32 10 1 0 0 0 1 0 0 0 1 3062b.DAT
> 1 8 40 56 0 0 0 1 0 1 0 -1 0 0 3023.DAT
> 1 8 -40 56 0 0 0 1 0 1 0 -1 0 0 3023.DAT
> 1 7 40 64 -10 0 0 1 0 1 0 -1 0 0 3623.DAT
> 1 7 -40 64 -10 0 0 1 0 1 0 -1 0 0 3623.DAT
> 1 0 0 0 -80 1 0 0 0 1 0 0 0 1 3024.DAT
> 1 0 0 0 -110 0 0 1 0 1 0 -1 0 0 4275.DAT
> 1 0 0 34 -148 -1 0 0 0 0 -1 0 -1 0 2880.DAT
> 1 7 0 74 -160 1 0 0 0 1 0 0 0 1 6120.DAT
> 0
|
|
Message is in Reply To:
 | | Re: Realistic landing gear for x-wing [DAT]
|
| Here's the landing gear I added to my X-Wing. The studs on the rear landing gear should go in the middle of the engines, and I attached the front landing gear on the nose right before the body gets wider. (If only hull bricks were only 1 brick (...) (26 years ago, 16-May-99, to lugnet.cad.dat.ideas)
|
6 Messages in This Thread:
 
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
