Special:
|
[DAT] (requires LDraw-compatible viewer)
|
Subject:
|
Re: Realistic landing gear for x-wing
|
Newsgroups:
|
lugnet.cad.dat.ideas
|
Date:
|
Sun, 16 May 1999 16:24:36 GMT
|
Viewed:
|
2561 times
|
| |
|
|
Here's the landing gear I added to my X-Wing. The studs on the rear
landing gear should go in the middle of the engines, and I attached the
front landing gear on the nose right before the body gets wider. (If
only hull bricks were only 1 brick wide--then you could make the landing
gear retract all the way into the nose.) As it is now, the landing gear
is still mostly visible when retracted. Please LMKWYT.
--Bram
0
1 7 50 0 -10 1 0 0 0 1 0 0 0 1 3794.DAT
1 7 -50 0 -10 1 0 0 0 1 0 0 0 1 3794.DAT
1 7 50 0 10 1 0 0 0 1 0 0 0 1 3794.DAT
1 7 -50 0 10 1 0 0 0 1 0 0 0 1 3794.DAT
1 7 40 8 0 0 0 -1 0 1 0 1 0 0 3938.DAT
1 7 -40 8 0 0 0 1 0 1 0 -1 0 0 3938.DAT
1 8 40 8 0 0 0 -1 0 1 0 1 0 0 3937.DAT
1 8 -40 8 0 0 0 1 0 1 0 -1 0 0 3937.DAT
1 7 40 32 -10 1 0 0 0 1 0 0 0 1 3062b.DAT
1 7 -40 32 -10 1 0 0 0 1 0 0 0 1 3062b.DAT
1 7 -40 32 10 1 0 0 0 1 0 0 0 1 3062b.DAT
1 7 40 32 10 1 0 0 0 1 0 0 0 1 3062b.DAT
1 8 40 56 0 0 0 1 0 1 0 -1 0 0 3023.DAT
1 8 -40 56 0 0 0 1 0 1 0 -1 0 0 3023.DAT
1 7 40 64 -10 0 0 1 0 1 0 -1 0 0 3623.DAT
1 7 -40 64 -10 0 0 1 0 1 0 -1 0 0 3623.DAT
1 0 0 0 -80 1 0 0 0 1 0 0 0 1 3024.DAT
1 0 0 0 -110 0 0 1 0 1 0 -1 0 0 4275.DAT
1 0 0 34 -148 -1 0 0 0 0 -1 0 -1 0 2880.DAT
1 7 0 74 -160 1 0 0 0 1 0 0 0 1 6120.DAT
0
|
|
Message has 2 Replies:
 | | Re: Realistic landing gear for x-wing
|
| My gear modifications are very close to yours, Bram. My rear gear is almost exactly like yours, in fact, except I only used one cylinder brick on each side, placed at the rear portion of the 1x2 tile. I used a similar concept that you used on the (...) (26 years ago, 17-May-99, to lugnet.cad.dat.ideas)
|
Message is in Reply To:
| | Realistic landing gear for x-wing [DAT]
|
| I finally got around to taking a couple of minutes to Ldraw this. I have shown the gear in landing and flight position. Depending on what you are using it on for a ship you might have to change it a little bit.This setup was off of the Z-95 that I (...) (26 years ago, 16-May-99, to lugnet.cad.dat.ideas)
|
6 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
