 | | Re: Pentapterigoid Star Fighter wallpaper
|
|
(...) I assume you're joking, but just in case - are you serious? Did you just convert another set into this? I don't even like most Space stuff, and I'd buy a few of these (your models) if you were selling. (25 years ago, 6-Jan-00, to lugnet.cad.ray, lugnet.publish)
|
| |
| | Re: A-Wing Fighter (MOC)
|
|
(...) D'oh! Guess I'm misremembering again. Jeff P.S. Thanks for the compliment! :) (25 years ago, 6-Jan-00, to lugnet.cad.dat.models)
|
| |
| | Re: getting started making pieces
|
|
(...) Welcome - new part authors are always welcome. The following is my preferred method of doing decorated parts as is a good grounding if you go on to author complete parts - others have had some success with BMP2DAT for decorated parts. 1. (...) (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
| |
| | getting started making pieces
|
|
A naive question perhaps, but I can't find the answer anywhere... I want to try my hand at making parts for ldraw, specifically I want to make minifig faces and torsos that haven't been done yet. What program(s) do you wizard-types use to make the (...) (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
| |
| | Re: Update 9906
|
|
(...) for (...) sample (...) Yes you're right, and I've done enough torsos that I should not have made such an error. Chris (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
| |
| | Small Pirate Hulls [DAT]
|
|
Here are the small hulls to go with the large ones I posted earlier. The mpd includes a test and also all 3 sections. 0 FILE hulls.dat 0 Hull Test Small 0 Author: Jonathan Wilson 1 6 0 0 0 1 0 0 0 1 0 0 0 1 6054.DAT 1 6 0 24 190 1 0 0 0 1 0 0 0 1 (...) (25 years ago, 6-Jan-00, to lugnet.cad.dat.parts)
|
| |
| | Re: Pentapterigoid Star Fighter wallpaper
|
|
(...) I don't think it would be too wise to try to find out. --Todd (25 years ago, 6-Jan-00, to lugnet.cad.ray, lugnet.publish)
|
| |
| | Re: Pentapterigoid Star Fighter wallpaper
|
|
(...) It's in stores now--haven't you seen it? Comes with 10 extra wings facing the opposite direction of the ones used in the model, all for $39.99! --Bram Bram Lambrecht / o o \ BramL@juno.com ---...---oooo-----(_...o---...--- WWW: (URL) PAYING (...) (25 years ago, 5-Jan-00, to lugnet.cad.ray, lugnet.publish)
|
| |
| | Re: Update 9906
|
|
(...) You're right, I gave that suggestion some time ago. The subpart only had the back surface when it was using the old number. Leonardo (25 years ago, 6-Jan-00, to lugnet.cad.dev)
|
| |
| | Re: part 2951, some questions [DAT]
|
|
(...) I will centre between the lower pegholes then. (...) Goood:) (...) correction: I will not put the measurements up, as they are changing as I get along. Look below for more on this. (...) As of now, it looks like the worst part is figuring out (...) (25 years ago, 5-Jan-00, to lugnet.cad.dev)
|
