To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.cadOpen lugnet.cad in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 CAD / *43861 (-10)
  Re: LPub Rotation Step angle woes
 
(...) I know. I used the form I did to confirm that the default viewing angle was mathematically messed up (and for dramatic emphasis). (...) I've got them, now it's time to test them. (...) Yes, actually, it was LDView that was confused. Travis' (...) (16 years ago, 7-Nov-08, to lugnet.cad.dev.mac, FTX)
 
  Re: LPub Rotation Step angle woes
 
(...) And you were right! The new version of LDView works. LDView 3.2 does not. Thanks very much for your help! Allen (16 years ago, 7-Nov-08, to lugnet.cad.dev.mac, FTX)
 
  Re: Is anyone working on 32745?
 
(...) Gosh. I forgot this thread. I have been working on this part for some time now, and I have a few things done (mainly the rear half, I was going to work on front part). I hope I have not duplicated too much of your work. Could you keep me in (...) (16 years ago, 7-Nov-08, to lugnet.cad.dat.parts)
 
  Re: LPub Rotation Step angle woes
 
(...) Well, Allen said that the LDView 4 test build fixed the problem. At a guess, LPub using -cg on the command line (to set the camera angle to 0 so that all the rotation can be in the model itself?) and the QT version isn't handling that like it (...) (16 years ago, 7-Nov-08, to lugnet.cad.dev.mac, FTX)
 
  Re: LPub Rotation Step angle woes
 
(...) Please note that instead of "0 ROTSTEP 0 0 0 REL", the preferred meta command is "0 ROTSTEP END". (...) There are 4 kinds of ROTSTEPS: REL, ABS, ADD, END For REL, you add the angles from the ROTSTEP meta to the default viewing angle to get the (...) (16 years ago, 6-Nov-08, to lugnet.cad.dev.mac, FTX)
 
  Re: LPub Rotation Step angle woes
 
(...) The more I think about it, the more I suspect that LDView 3.2 on the Mac is to blame. I sent Allen an email with a link to an LDView 4 test build. --Travis (16 years ago, 6-Nov-08, to lugnet.cad.dev.mac, FTX)
 
  Re: LPub Rotation Step angle woes
 
(...) snip (...) Alas. That is what I'm supposed to see, not what I actually do see. Something is convinced that the 0,0,0 rotation is actually equal to the default 3D angle, which causes requests for the real default 3D angle to be over-rotated. (...) (16 years ago, 6-Nov-08, to lugnet.cad.dev.mac, FTX)
 
  Re: personal OMR (now 879 sets)
 
(...) If you have looked carefully throught all the stuff you would have seen that not all are done by myself! I also like if I get models build by others to put into that OMR! cu mikeheide (16 years ago, 4-Nov-08, to lugnet.cad.dat.models)
 
  Re: personal OMR (now 879 sets)
 
(...) much time on your hands! :-) (16 years ago, 4-Nov-08, to lugnet.cad.dat.models)
 
  Re: LPub Rotation Step angle woes
 
(...) It is not coincidence that it works. LPub is written to handle it your way. STEPs and ROTSTEPs that are not preceded by type 1 through 5 lines are not treated as step. (...) Kevin (16 years ago, 4-Nov-08, to lugnet.cad, FTX)


Next Page:  5 more | 10 more | 20 more

Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR