 | | Re: Slope Brick 1x1
|
|
(...) With the notable exception of the 45 degree slopes, none of the other slope parts have exactly the inclination used in the part description. Note that all have a small vertical section (or step) at the front which causes the angle to deviate (...) (16 years ago, 30-Sep-08, to lugnet.cad.dat.parts)
|
| |
| | Zaku II - 4884 alternate model [DAT]
|
|
model page announced here: (URL) Zaku II - 4884 Wild Hunters alternate model 0 may include unofficial parts 0 WRITE Author: Joseph Gonzalez (c) 2008 0 Unofficial Model 0 IMPORTANT: Zaku and Gundam is a registered trademark of Sotsu Agency Co. 0 (...) (16 years ago, 30-Sep-08, to lugnet.cad.dat.models)
|
| |
| | Re: LPub4.0.0.1 available
|
|
(...) It is indeed. I need to place another bufferexchange there. (16 years ago, 29-Sep-08, to lugnet.cad)
|
| |
| | Re: LPub4.0.0.1 available
|
|
I found one more thing. It appears that at least one of the parts placed in step 7 gets left around inside the model, and is just visible in step 15 as a black rectangle in the center of the bottom. The is visible in both versions of the PDF. (...) (16 years ago, 29-Sep-08, to lugnet.cad)
|
| |
| | Re: LPub4.0.0.1 available
|
|
(...) You missed a difference on Page 2. In the bottom part, the green arrows are shown in the 4.0.0.1 version, and not in the other version. (...) And round light grey plate 1x1 is not shown either. --Travis (16 years ago, 29-Sep-08, to lugnet.cad)
|
| |
| | Re: LPub4.0.0.1 available
|
|
(...) I am looking forward to the results, as I am due to deliver building instructions for a project I am working on. I have sent you some personal E-mails about this too. Once again, I thank _you_ for all you effords in creating LPub. (16 years ago, 29-Sep-08, to lugnet.cad)
|
| |
| | Re: Slope Brick 1x1
|
|
Right. So who is to change the name then? Peeron or LDraw? (16 years ago, 29-Sep-08, to lugnet.cad, lugnet.off-topic.geek)
|
| |
| | Re: Slope Brick 1x1
|
|
(...) But if you use the part properly* it's 31 degrees. The 45 slope is named for its face slope rather than its total slope. Tim * And by properly I, of course, mean use a heap of offsetting to make them all line up ;) (16 years ago, 29-Sep-08, to lugnet.cad, lugnet.off-topic.geek)
|
| |
| | Re: LPub4.0.0.1 available
|
|
(...) Jaco, Thanks for your detailed analysis complete with MPD to allow recreation. I will take if rom here and fix the LPub bugs. Kevin (16 years ago, 29-Sep-08, to lugnet.cad)
|
| |
| | Re: LPub4.0.0.1 available
|
|
(...) OK, while testing and playing around with LPub 4 I tried some new techniques I've come up with. I've recreated the "exact" instructions for set 4491. (URL) the same file in LPub 4.0.0.0 and 4.0.0.1 gives different outputs. I've uploaded the (...) (16 years ago, 29-Sep-08, to lugnet.cad)
|
