 | | Re: door 1 x 3 x 1 new patterns and errors in parts on PT
|
|
(...) Thanx for the quick response. If you create a subpart with the police pattern, could you please put only the area where the text police fits in into that subpart and not the surrounding border to fill up a brick. (just like the fire logo and (...) (21 years ago, 12-May-03, to lugnet.cad.dat.parts)
|
| |
| | Re: door 1 x 3 x 1 new patterns and errors in parts on PT
|
|
(...) As soon as I get my PT access restored, I'll make this correction. Thanks for picking up on this. (...) I picked p18 for police because it was unused across a large variety of parts. There's a variation on the POLICE pattern for the 1 x 4 x 3 (...) (21 years ago, 12-May-03, to lugnet.cad.dat.parts)
|
| |
| | Re: Parts - Aquanauts Door and Door Frame
|
|
(...) for them. There must be a glitch in Peeron somewhere. For reference, the Peeron names for these parts are 2596 Door 1 x 9 x 11 2662 Door Frame 2 x 8 x 12 -- TWS Garrison (URL) capital letters in address for direct reply. (21 years ago, 12-May-03, to lugnet.cad.dat.parts)
|
| |
| | door 1 x 3 x 1 new patterns and errors in parts on PT
|
|
Browsing the PT for the new subpart for the door 1 x 3 x 1 without stud I also took a look at the complete door parts on the PT and noticed the following errors in two parts: 3822p03 Door 1 x 3 x 1 Left with Yellow / Red Stripe Pattern Misspelled (...) (21 years ago, 12-May-03, to lugnet.cad)
|
| |
| | Parts - Aquanauts Door and Door Frame
|
|
Dear All, I am about to finish new parts: 2662 - Aquanaut Door Frame 2596 - Large Aquanaut Door You can see pictures here (URL) opinion Bricklink has better names for them. Please see here (URL) - Door Frame with Hinges 2596 - Door 1 x 9 x 11 with (...) (21 years ago, 12-May-03, to lugnet.cad, lugnet.cad.dat.parts)
|
| |
| | Re: uCOG V - my tiniest weight shifting walker
|
|
Hi Philo, Great minds think alike. I did the same last night. I've got one build with studs up, and a second with studs down. I'm going to update the building instructions, and post the DAT files as well. I figure it is a good example of the new (...) (21 years ago, 12-May-03, to lugnet.technic, lugnet.cad, lugnet.inst, lugnet.robotics)
|
| |
| | Re: Partnames and patternumbers requested
|
|
(...) Will do. Steve (21 years ago, 12-May-03, to lugnet.cad)
|
| |
| | Re: Another question about metal parts
|
|
(...) That sounds alright to me. Steve (21 years ago, 12-May-03, to lugnet.cad)
|
| |
| | Re: uCOG V - my tiniest weight shifting walker
|
|
...I forgot to tell you that I built mine using one top (2984) and one base (2985) micromotor caps instead of two tops, and it works well (useful since micromotor is/was supplied with one part of each type...) Philo (...) (21 years ago, 12-May-03, to lugnet.technic, lugnet.cad, lugnet.inst, lugnet.robotics)
|
| |
| | Re: Bendible parts Web Page
|
|
Yeah! I can't say right now that I would use it, but I have wanted the ability every now and then. And I am always for any software that will run on Macintosh, even if it is through a webpage (which is what you describe sounds like). James (...) (21 years ago, 12-May-03, to lugnet.cad.dev)
|
