 | | m6606 [DAT]
|
|
Road repair set 0 Road repair set 0 Name: m6606.ldr 0 Author: C.Daelman <cdaelma@pi.be> 0 Official Repository Model 0 WRITE Step 1 1 0 0 0 0 0 0 1 0 1 0 -1 0 0 3020.DAT 0 STEP 0 WRITE Step 2 1 0 -10 -8 -30 1 0 0 0 1 0 0 0 1 4085A.DAT 1 0 10 -8 -30 1 (...) (22 years ago, 22-Sep-02, to lugnet.cad.dat.models.sets)
|
| |
| | Re: "Part Unknown!" warning, what does it mean
|
|
(...) You should download and use the revised part: (URL) (22 years ago, 22-Sep-02, to lugnet.cad.mlcad)
|
| |
| | Minifog Torso diagonal Edge
|
|
The pattern I am working on has a lot of fine detail that is pretty close to the edge. The large diagonal edge on each side is giving me some trouble... Just using one trapezoid from the top edge corner to the bottom (taking up the whole diagonal) (...) (22 years ago, 22-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Orientation of part x464.dat
|
|
(...) Oh. You're right. I saw it as a brick rather than a slope. :o) /Tore (22 years ago, 22-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Orientation of part x464.dat
|
|
(...) No, it should (and does) have the same orientation as other sloped parts: the primary slope faces the Z- axis. Steve (22 years ago, 21-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: (number needed) - Slope Rounded Inverted 1 x 6
|
|
Hehe, Mega-oops! Here's the correct header: 0 Slope Rounded Inverted 1 x 6 0 Name: ???.dat 0 Author: Tore Eriksson 0 Based on x464.dat by Franklin W. Cain (fwcain@yahoo.com) 0 Unofficial Element 0 BFC NOCERTIFY (22 years ago, 21-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | Re: How accurate need bricks to be?
|
|
(...) Yes, this is the "rule" we try to apply - if the detail is functional, then it should be included, if decorative or an artifact of the moulding process then it may be ignored. So in your two examples, I would expect to see the small lugs on (...) (22 years ago, 21-Sep-02, to lugnet.cad)
|
| |
| | Sticker parts numbers (was Re: How accurate ....)
|
|
(...) Where we stil have access to the sticker sheet I believe there was agreement to use the sticker sheet number with a one-letter suffix for each unique sticker on the sheet. Hence 168135a et seq submitted to the PT by Imre Papp. A brief review (...) (22 years ago, 21-Sep-02, to lugnet.cad)
|
| |
| | Re: #902 / Old parts
|
|
(...) Alright, a crude mockup is posted at lugnet.cad.dat.parts. It should be quite useful, since when built in a model, the simplifications will be hard to discover. (22 years ago, 21-Sep-02, to lugnet.cad)
|
| |
| | New Part Mockup: 3404b.dat - Turntable 4 x 4 Top, Old [DAT]
|
|
0 Turntable 4 x 4 Top, Old (mockup) 0 Name: 3404b.dat 0 Author: Tore Eriksson 0 Unofficial Part 0 BFC NOCERTIFY 1 14 -10 0 30 1 0 0 0 1 0 0 0 1 stud.dat 1 14 10 0 30 1 0 0 0 1 0 0 0 1 stud.dat 1 14 -30 0 10 1 0 0 0 1 0 0 0 1 stud.dat 1 14 -10 0 10 1 (...) (22 years ago, 21-Sep-02, to lugnet.cad.dat.parts)
|
