 | | Re: Ldraw and Ledit in windows xp?
|
|
(...) Where can I find it? That link you gave me gives a 404 error. (23 years ago, 4-Jan-02, to lugnet.cad)
|
| |
| | Re: Ldraw and Ledit in windows xp?
|
|
"Bram Lambrecht" <bram@cwru.edu> wrote in message news:000101c194a9$ec...1681@bl... (...) Download ldraw027.exe, it comes pre-patched for error 200. They disappeared because the new release eliminated the need for them. (...) (23 years ago, 4-Jan-02, to lugnet.cad)
|
| |
| | Re: 30293 & 30294 Anyone ?
|
|
no. I got distracted by another part and haven't started on these yet : ( Jake McKee <sink@countersinkdg.com> wrote in message news:GpE7Ey.J5H@lugnet.com... (...) (23 years ago, 4-Jan-02, to lugnet.cad.dat.parts)
|
| |
| | Re: 30293 & 30294 Anyone ?
|
|
(...) Did you have any luck on this? Jake --- Jake McKee AFOL LUGNET Member #211 (23 years ago, 4-Jan-02, to lugnet.cad.dat.parts)
|
| |
| | alignment newbie question
|
|
Hi I created this model using mlcad and used l3pao and pov-ray to render.The parts look okay in mlcad but after rendering I noticed missaligned pieces. Can anyone explain what I did wrong and is their a quick fix or how would you fix it? thanks here (...) (23 years ago, 4-Jan-02, to lugnet.cad)
|
| |
| | Re: LDGLite colour bug
|
|
(...) the OSMesa driver on ldraw.org. Its reproducible with just two stud3.dats or even just two 4-4disc4.dats. And it only seems to happen when lighting is enabled and and antialiased edgelines are on, even if you don't have any edgelines. I wonder (...) (23 years ago, 3-Jan-02, to lugnet.cad.dev)
|
| |
| | RE: Ldraw and Ledit in windows xp?
|
|
(...) I get a Run Time Error 200...and the patch seems to have disappeared from ldraw.org. In any case, I can't find a link to it. --Bram Bram Lambrecht bram@cwru.edu www.bldesign.org (23 years ago, 3-Jan-02, to lugnet.cad)
|
| |
| | Re: Can LDGLite print the current orientation matrix? (feature request)
|
|
(...) Probably not. I can run L3Lab under Linux using Wine, but that is on an i686 based computer, not Alpha. Fredrik (23 years ago, 3-Jan-02, to lugnet.cad.dev)
|
| |
| | Re: Proposal: New Parts Category for round parts
|
|
(...) I think this sounds like a sensible approach! (...) You mean something like 2637 Technic Axle 16 with Axleholes 2739 Technic Axle 6 with Ball Joint Sockets I am a bit ambivalent about this. The rods in question are axle shaped, however they (...) (23 years ago, 3-Jan-02, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: x191 & x192 part in the Parts tracker
|
|
(...) Hallo Carsten, First of all, Best Wishes for the New Year, or should i say : Prosit Neujahr ? 1) Thanks a lot for the info. I will remove the electric wire at the point where it leaves the connector, so that you can't look through the part (...) (23 years ago, 1-Jan-02, to lugnet.cad.dat.parts)
|
