 | | Re: New Scenes at BrickDreams, and Thanks
|
|
(...) It's fine, but you might want to set the 'Followup-To:' header to point at lugnet.cad.ray if you expect the discussion to wander in that direction (like, let's say, in-depth discussion of the tools you used and things like that). Otherwise, (...) (24 years ago, 25-Mar-01, to lugnet.general, lugnet.cad.ray, lugnet.publish, lugnet.admin.nntp)
|
| |
| | Re: New part from Mawhonic's Pod Racer. . . [DAT]
|
|
Franklin, Ugh, you are correct! This is what happend when you work on a part for in excess of 6 hours! Your brain becomes fried and you cannot think anymore. I appreciate your correction :). Later, Scott 0 Tile 2 x 2, with Star Wars Mawhonic's Pod (...) (24 years ago, 24-Mar-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New part from Mawhonic's Pod Racer. . .
|
|
(...) I'm pretty certain that you must mean "Watto's Junkyard" set number 7186. Set # 7171 contained the Pod Racers for Anakin, Sebulba, and Gasganno [sp?]. Hope this helps. Franklin (24 years ago, 24-Mar-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Classic Space Sets in CAD?
|
|
Kyle, It so happens that I have produced a few of the Classic Space sets. (one of them is even post in lugnet.cad.dat.models) E-mail me and I will send you all the .DAT files you need for: #6824 - Space Dart I (with figure and radio) #6845 - Cosmic (...) (24 years ago, 24-Mar-01, to lugnet.space, lugnet.cad.dat.models.sets)
|
| |
| | Re: Rotation trouble
|
|
Hey, There should be some buttons with arrows going around axes. These control the rotation of an element around the x, y, and z axes. The degree of rotation is determined by the grid icon. You can also edit the amount of rotation by going to (...) (24 years ago, 24-Mar-01, to lugnet.cad.mlcad)
|
| |
| | New part from Mawhonic's Pod Racer. . . [DAT]
|
|
Hey, I just finished a long session of figuring out a little bit about rings and stuff. Well, here is the fruit of about 6 hours of tinkering. This is the 2 x 2 tile from Mawhonic's Pod Racer Engine from 7171 - Mos Espa Poad Race. I hope it's (...) (24 years ago, 24-Mar-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Parts Tracker Prototype Posted
|
|
(...) If the server is a UNIX server then maybe you can use RCS - I think this change/version control system is implemented on most commercial UNIX platforms and is not difficult to use. In addition to the file locking it could also give you version (...) (24 years ago, 24-Mar-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Rotation trouble
|
|
Hey Dug, I have had some difficulty with that at times as well. One way I began to over come the problem was to open the rotation dialog bod and go to the bottom text window (you have to click the radio button to enable it). And enter "1 0 0 0 1 0 0 (...) (24 years ago, 24-Mar-01, to lugnet.cad.mlcad)
|
| |
| | Rotation trouble
|
|
Hi all, I'm pretty much new to MLcad, although I'm not quite new to the world of CAD. I had some trouble after rotating a part at 45deg. After that I couldn't get the rotation angle back to 90.... Pieces were rotating all over the place, but not at (...) (24 years ago, 24-Mar-01, to lugnet.cad.mlcad)
|
| |
| | New Scenes at BrickDreams, and Thanks
|
|
Scene #7 has now been released, and you can see a preview of Scene #8, which is currently burning away in Bryce on my other computer. I estimate the scene will be finished in about 16 hours, give or take a few. The 128x96 preview image alone took (...) (24 years ago, 23-Mar-01, to lugnet.general, lugnet.announce, lugnet.cad.ray)
|
