 | | Re: Motorcycles??
|
|
(...) They have? I don't remember getting them.... Steve (24 years ago, 30-Oct-00, to lugnet.cad.dat.parts)
|
| |
| | Re: Minifig Round Shield
|
|
(...) I thought the raised areas were rounded. Then again, my attempt at this part was over 100K. Steve (24 years ago, 30-Oct-00, to lugnet.cad.dat.parts)
|
| |
| | Re: 4150p101.dat - tile 2 x 2 w/ SW imperial pattern
|
|
(...) Good, I feel a lot better now. There is a fine line between getting stuff right by judicious use of group critical appraisal, and squelching enthusiasm. I am glad to see that's not the case and you're cranking out more parts! Keep at it! Since (...) (24 years ago, 30-Oct-00, to lugnet.cad.dat.parts)
|
| |
| | Parts tracker needs more visibility (was Re: 4150p101.dat - tile 2 x 2 w/ SW imperial pattern
|
|
(...) And *that* is why the parts tracker URL needs to be listed on the web front page of the cad.dat.parts group. Todd Lehman, can you fix that, please? Thanks! ++Lar (24 years ago, 30-Oct-00, to lugnet.cad.dat.parts, lugnet.admin.general)
|
| |
| | Part repost: 4150p102.dat: Tile 2x2 with Hologameboard pattern [DAT]
|
|
With a better filename. By the way, anyone know what the part number for the chain seen in set 3050 (Shanghai Surprise) might be? 0 Tile 2 x 2 Round with Djarik hologame board pattern 0 WRITE Author: Matt Schild 0 WRITE Unofficial part 0 WRITE Name: (...) (24 years ago, 30-Oct-00, to lugnet.cad.dat.parts)
|
| |
| | 3069p02.dat - Tile 1 x 2 with Tape Reels pattern [DAT]
|
|
Here's another one. Please LMKWYT. Thanks. (Tore, Someone requested this part, but gave it a slightly different name. Please use this name for the entry in your parts tracker. Thanks.) Thanks, Franklin 0 Tile 1 x 2 with Tape Reels pattern 0 (...) (24 years ago, 30-Oct-00, to lugnet.cad.dat.parts)
|
| |
| | Repost: 973p103.dat Minifig torso with Han Solo (with jacket) pattern [DAT]
|
|
With a better filename. 0 Minifig Torso with Han Solo pattern (with jacket, from set 7190) 0 Name: 973p103.DAT 0 Author: Matt Schild 0 Unofficial part 0 ROTATION CENTER 0 0 0 1 "Custom" 0 ROTATION CONFIG 0 1 1 16 0 0 0 1 0 0 0 1 0 0 0 1 s\973s01.dat (...) (24 years ago, 30-Oct-00, to lugnet.cad.dat.parts)
|
| |
| | Re: Follow up to Camera Tricks
|
|
Hi, I was having problems because the PCT value was not set at 0 so the values I inputted for the camera position put the camera in a place I did not expect. Thanks Jay Jacinto (...) if (...) (24 years ago, 30-Oct-00, to lugnet.cad.mlcad)
|
| |
| | Re: Follow up to Camera Tricks
|
|
OIC Thanks Jay Jacinto (...) (24 years ago, 30-Oct-00, to lugnet.cad.mlcad)
|
| |
| | Re: Follow up to Camera Tricks
|
|
Think of "angle" as "zoom". The smaller the number, the "closer" you are to the object. The larger the number, the "further away" you are. Royce (...) (24 years ago, 30-Oct-00, to lugnet.cad.mlcad)
|
