 | | Different arangement in view- and construct-mode
|
|
I had this thought about MLcad: What about having different settings (not settings in the menu) for view-mode and construct-mode (place/move/size)? So that you could arrange viewports (window), toolbars and part-viewer differently. I would like to (...) (25 years ago, 9-May-00, to lugnet.cad.mlcad)
|
| |
| | Re: Sv: Bugfix Release of MLCad & More
|
|
Since you are waiting already, I will report a bug. When I try to rotate a model in the 3D view using the mouse, it fails when the model is complex. It pauses for a little while, then just returns to normal mode. It never goes into wireframe mode. (...) (25 years ago, 9-May-00, to lugnet.cad, lugnet.cad.mlcad)
|
| |
| | Re: reminder: bug in piece #2500c01
|
|
(...) It should be 4-4con1.dat. I will make sure this is fixed. In the next update. (...) I haven't seen l3lab complain about 2-4edge. L3lab certainly doesn't like s\973s01.dat, the blank subpart for the minifig torso, because the printed rectangle (...) (25 years ago, 9-May-00, to lugnet.cad.dev)
|
| |
| | Re: Sv: Bugfix Release of MLCad & More
|
|
(...) <SNIP> Yep, you are right ==> corrected it already ... but I'm waiting now for two days! until I release it (just in case :-) Also I'm currently directly talking to Axle because of this rotation dialog problem. Michael (25 years ago, 9-May-00, to lugnet.cad, lugnet.cad.mlcad)
|
| |
| | Re: LCad Parts Update 2000-01 Now Available
|
|
(...) Augh. My mistake - I was trying to reduce the occurance of 'singular matrix' warnings, and wasn't careful enough while editing. (...) Generally, when you've got a obvious fix like this, just send it to partsref (IMO). If there's an issue that (...) (25 years ago, 9-May-00, to lugnet.cad)
|
| |
| | Re: LCad Parts Update 2000-01 Now Available
|
|
(...) Erk. You are correct, the 48\1-8edge.dat primitive should have been included with this update. My bad. Steve (25 years ago, 9-May-00, to lugnet.cad)
|
| |
| | Re: Bugfix Release of MLCad & More
|
|
In lugnet.cad, Axel Poqué writes: <SNIP> I changed the numbers until L3lab loaded the part without complaint, then tried (...) mouse (...) says (...) done (...) program. (...) Agreed: Pressing CANCEL is ignored by MLCad ==> bug I could see a problem (...) (25 years ago, 9-May-00, to lugnet.cad, lugnet.cad.mlcad, lugnet.trains)
|
| |
| | Re: Bugfix Release of MLCad & More
|
|
(...) This is the right behavior (at least until now) if you select absolute rotation angles. In this case MLCad ignores all view angles and uses the specified one instead. The rotation end step reverts back to the original rotation angles. Michael (25 years ago, 9-May-00, to lugnet.cad, lugnet.cad.mlcad, lugnet.trains)
|
| |
| | Re: Bartleby Render: attn Todd
|
|
(...) Everybody run!!! --Todd (25 years ago, 9-May-00, to lugnet.cad.ray)
|
| |
| | Bartleby Render: attn Todd
|
|
I got a quick render of the Bartleby tank done. Is this what you had in mind in your request Todd? I like this prospective. I need to figure out how to add some "atmosphere" to the scene to make it more real looking. All in good time I guess. Here's (...) (25 years ago, 9-May-00, to lugnet.cad.ray)
|
