 | | Re: New Part: Technic Steering Knuckle
|
|
Looks great. Not the one I need, though. Bummer. (25 years ago, 5-May-00, to lugnet.cad.dat.parts)
|
| |
| | Re: MLCAD for Mac??
|
|
Steve Bliss wrote... (...) Try (URL) and go to (URL) (25 years ago, 5-May-00, to lugnet.cad.dev)
|
| |
| | New Part: Technic Steering Knuckle [DAT]
|
|
This is the part as seen in step 27 of: (URL) I don't know the part number for this one. I may have got a few of the type 5 lines messed up. Let me know what you think. -Thanks Chris P.S. part 6572 to follow shortly (1x3 liftarm with towball) the (...) (25 years ago, 5-May-00, to lugnet.cad.dat.parts)
|
| |
| | request for comments: ATSTEP meta command
|
|
I've been frustrated by trying to use STEP to create instruction sheets. Typical problems: I need step 3 to have the model upside down; I need step 5 to be a sub-assembly that gets added in step 6 to the parts in step 4; etc. I've had limited (...) (25 years ago, 5-May-00, to lugnet.cad)
|
| |
| | Re: new renderings
|
|
whoops that wasnt supposed to be a reply.... sorry -Phil (...) the (...) (25 years ago, 5-May-00, to lugnet.cad)
|
| |
| | new renderings
|
|
Hello all, i just thought i'd announce that i've added some new renderings at (URL) has a lot of land stuuf and a pic of a torpedo and a car that looks like the General Lee. -Philip Kostka seahaus@znet.com (URL) (25 years ago, 5-May-00, to lugnet.cad)
|
| |
| | Re: LDraw Add-On Version 2.1.3
|
|
Steve Bliss skrev i meddelandet ... (...) I tried it, and the stub exe downloaded OK. When I run it, I'm guided through the wizard dialogs, and finally it will start to check the files to download. It skips files I already have, and then, when it (...) (25 years ago, 4-May-00, to lugnet.cad)
|
| |
| | Re: MLCAD for Mac??
|
|
(...) I'd start at (URL). Or read through the lugnet.cad.mlcad group. Steve (25 years ago, 4-May-00, to lugnet.cad.dev)
|
| |
| | Re: Suggestions for new primitives: Flex-System hoses.
|
|
(...) Yeah, I'll run the primitive past the committee. A couple of things stand out immediately: - The primitive's name should be 4-4con8.dat, not 4-4co89.dat. - Primitives (especially the curved variety) should go to 4 decimal places. Actually, I (...) (25 years ago, 4-May-00, to lugnet.cad.dev)
|
| |
| | Re: Technic Ribbed Hose (Example MPD file) [DAT]
|
|
[X-FUT lugnet.cad.dat.parts...rimitives] 0 FILE 4-4con8.dat 0 4/4 Cone Section 8:9 Radius 0 Name: 4-4con8.dat 0 Unofficial Primitive 0 BFC CERTIFY CW 5 24 8 1 0 9 0 0 7.3912 1 -3.0616 7.3912 1 3.0616 5 24 7.3912 1 3.0616 8.3151 0 3.4443 8 1 0 5.6568 (...) (25 years ago, 4-May-00, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives)
|
