 | | Re: Help ID pieces
|
|
(...) Had a look in Tim Vattima's inventory and there are a few possibilities, check here: (URL) top level of Tim's database is here: (URL) , also accessible from the LUGnet main page.) Indispensible resource! Heather St. John's, Newfoundland, (...) (25 years ago, 9-Jul-99, to lugnet.build)
|
| |
| | Re: Solar Power & LEGO
|
|
(...) Thanks. I just visited the Edmunds Scientic Page and they said their solar panels can be wired in series. The thing I need to know now is how many volts and how many amps is appropriate for powering the Rcx. I assume 9 volts. But is 12 volts (...) (25 years ago, 9-Jul-99, to lugnet.build)
|
| |
| | Re: Solar Power & LEGO
|
|
(...) The solar panels from Radio Shack can be wired in serial. I belive one rail is the + and the other - . (25 years ago, 9-Jul-99, to lugnet.build)
|
| |
| | Solar Power & LEGO
|
|
Anybody done it? I would like to incorporate solar power into lEGO and perhaps LEGO robotics. In fact, I have never used solar power (SP) for anything. I have heard that the TAMAYKO (sp?) plastic model kit from Japan has a good solar panel but it (...) (25 years ago, 9-Jul-99, to lugnet.build)
|
| |
| | Re: Does Pneumatic Suck?
|
|
Maico Arts wrote in message ... (...) But you can also make them "sucking" by mechanically pulling or pushing the piston. Their working principle is applying pressurized air to the one face of the piston, then piston goes opposite side, right*. so (...) (25 years ago, 9-Jul-99, to lugnet.build, lugnet.robotics)
|
| |
| | Re: Does Pneumatic Suck?
|
|
Hello Try to get one of the early technic pneumatic sets, like the 8851 or 8843 TRhese set have a grey 4 x 2 brick with valves. This pump pushes the air through one side of the brick and sucks the out of the brick using the other valve. These (...) (25 years ago, 9-Jul-99, to lugnet.build, lugnet.robotics)
|
| |
| | Does Pneumatic Suck?
|
|
Hi Technic heads, Is it possible to build a pneumatic _SUCTION_ system using only LEGO parts? I've seen many pneumatic PUMP systems. But my goal is to have a MindStorms controlled suction system that can lift a LEGO brick (on the flat side of (...) (25 years ago, 9-Jul-99, to lugnet.build, lugnet.robotics)
|
| |
| | Re: The Construction Paper
|
|
(...) Think Diagonal. You may get a few more studs that way, not sure, depends on the width (25 years ago, 8-Jul-99, to lugnet.build, lugnet.loc.us.ma.bos)
|
| |
| | Re: Help ID pieces
|
|
(...) I don't see any other Paradisa parts. I think they must have come from multiple copies of 6552 Rocky River Retreat, but I only have enough parts to complete one of the sets. I suspect the boys I bought the LEGO from received identical sets so (...) (25 years ago, 8-Jul-99, to lugnet.build)
|
| |
| | Re: Help ID pieces
|
|
(...) 6405 Sunset Stables as well; the Paradisa pieces in both sets are obvious, I'm sure, if that's what you have. (25 years ago, 8-Jul-99, to lugnet.build)
|
| |
| | Re: The Construction Paper
|
|
(...) That's just over 38 studs - a bit tight for a decent car, which is really all I can build. I've got an (already too-short looking) El Camino standing here that would fit if I take off the rear bumper corners, I guess BTW: It's got an (...) (25 years ago, 8-Jul-99, to lugnet.build, lugnet.loc.us.ma.bos)
|
| |
| | Re: Help ID pieces
|
|
(...) 6363(?), 6521 (...) 1722, 6593, 6612, 6643, 9365 (...) 6544 (...) 6342, 6347(?), 6338(?) (...) Selçuk (25 years ago, 8-Jul-99, to lugnet.build)
|
| |
| | Re: Help ID pieces
|
|
(...) (URL) I got the hull and some of the parts for 4021 in a big ship parts lot. (25 years ago, 8-Jul-99, to lugnet.build)
|
| |
| | Re: Help ID pieces
|
|
(...) That fits with some other pieces I have. Unfortunately, the side panels are missing. (...) I was hoping there was another set with that tile. I have enough parts to complete one 6593, but no ladder or hose winch for a second set. (...) (...) (25 years ago, 8-Jul-99, to lugnet.build)
|
| |
| | Re: Help ID pieces
|
|
(...) 6521 Emergency Repair Truck, probably. The giveaway would be the printed 1x2x2 panels. (...) I have one in a 6593 Blaze Battler - there's also a 2x4 hose winch and frame with flame logo. (...) One of the Launch Command sets? (...) Dunno, (...) (25 years ago, 8-Jul-99, to lugnet.build)
|
| |
| | RE: Help ID pieces
|
|
John Kornhaus wrote (...) This is a sigline I have not seen before, and it is sufficiently obscure to be useful only on lugnet. Unfortunately, it is also very true.... Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (...) (25 years ago, 8-Jul-99, to lugnet.build)
|
| |
| | Help ID pieces
|
|
I just emerged from my dark ages and bought a box of LEGO with no instructions at a yard sale. I've had pretty good luck (and a lot of fun!) re-constructing most of the sets, but I have some pieces left that I can't assign to sets. Can anyone help (...) (25 years ago, 8-Jul-99, to lugnet.build)
|
| |
| | Re: Piece ID
|
|
(...) Yup, that's it. I suspected it would be a Fabuland part. (25 years ago, 8-Jul-99, to lugnet.build)
|
| |
| | Re: Piece ID
|
|
Selçuk wrote in message ... (...) Wow, I was correct. Just checked fabuland pictures, and saw it. See 3671, 3672, and/or 3678 from pause. Selçuk (25 years ago, 8-Jul-99, to lugnet.build)
|
| |
| | Re: Piece ID
|
|
Frank Filz wrote in message <37839555.A16@mindsp...ng.com>... (...) Just a rough guess but it could be a Fabuland furniture part, probably a chair. Selçuk (25 years ago, 8-Jul-99, to lugnet.build)
|
