 | | Re: New Crane...
|
|
(...) This is correct. Real cranes have roller bearings that are pinned in place that bear the weight and force of the superstructure where it is connected to the base. (...) I am going to use a threaded axle through the center to hold the plates (...) (17 years ago, 21-Feb-08, to lugnet.technic)
|
| |
| | Re: It’s the year 2008, where are my parts updates?
|
|
(...) To answer both of your questions, take a look at LDraw.org's (URL) Unofficial Parts> page. Although the 'instructions' are kinda brief. Sorry about that. Basically, you do this: Download the zip file (the link at the bottom of the unofficial (...) (17 years ago, 21-Feb-08, to lugnet.cad, FTX)
|
| |
| | Re: Which glue?
|
|
(...) Brian, I would try a dab of silicone adhesive caulk. You can check the specs but think would be good down to -60----if not there are some that are. Messy but would bet it would work. Also, try roughing up the beam with bit of sandpaper which (...) (17 years ago, 21-Feb-08, to lugnet.parts.mod)
|
| |
| | Re: It’s the year 2008, where are my parts updates?
|
|
(...) Are there instructions anywhere on how to download and install or update unofficial parts? Is there a repository where all the unofficial parts live? Thanks, Paul Sinasohn LUGNET #115 (17 years ago, 21-Feb-08, to lugnet.cad)
|
| |
| | How do -you- clean your LEGO parts?
|
|
I don't think LUGNET has had any discussions about this in quite some time. How do -you- clean your LEGO parts? I'm interested in learning people's techniques, particularly ones that clean a lot of parts at once with little effort. LEGO that's been (...) (17 years ago, 21-Feb-08, to lugnet.general, lugnet.parts)
|
| |
| | Re: Exhaust Pipes 71137 and x855 misaligned
|
|
(...) Thanks for checking, I posted a warning on PT. BTW, part number is 40620. Philo (17 years ago, 21-Feb-08, to lugnet.cad.dat.parts)
|
| |
| | What should happen with the lugnet.robotics.nxt sidebar?
|
|
Hello, LUGNET readers. In case you don't know, I'm the lugnet.robotics.nxt curator. I used to update the NXT section sidebar with [in]frequent regularity, but during the last couple months I've not done anything to it. I get busy and/or don't take (...) (17 years ago, 21-Feb-08, to lugnet.robotics.nxt, lugnet.technic, lugnet.general, lugnet.admin.curators)
|
| |
| | Re: Exhaust Pipes 71137 and x855 misaligned
|
|
(...) This problem should be fixed with the update I made in November 2007! Do you have noticed that? cu mikeheide (17 years ago, 21-Feb-08, to lugnet.cad.dat.parts)
|
| |
| | Urban Pool Hall
|
|
Hello, I had been uninspired lately but broke out of it (for a little while, anyway) to build this Pool Hall. I hope this is the first of many more buildings for my new layout. (Urban Landscape 2008/2009) (4 URLs) After mod: (URL) This was built on (...) (17 years ago, 21-Feb-08, to lugnet.announce.moc, lugnet.town) !!
|
| |
| | Re: Which glue?
|
|
(...) Brian, Have you tried Gorilla Glue? You just have to be careful not to use too much as it expands as it dries. I'm also assuming that it's the flat-plain side(s) of the beam (not the technic pin hole side(s) ) that you are trying to affix to (...) (17 years ago, 21-Feb-08, to lugnet.parts.mod)
|
