 | | Re: Part number needed & New primitive submission
|
|
(...) You are right about the rotation point. It should lie on a major axis, to simplify rotating. However, I believe most window panes have been created in their 'default' orientation, not laying on their side. If you rotate this part 90-degrees (...) (25 years ago, 29-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Re: pneumatics & mindstorms?
|
|
(...) sequence (...) only (...) 51.99 FF, that means 7.93 Euros. About 8.40 USD at current exchange rate. The problems is they don't ship abroad. To get them here in Italy I had to send a check in FF and ask them for shipping to a French address (my (...) (25 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
| | Re: what are the rules about hoses etc?
|
|
(...) You can create a reasonable rendition of a Technic hose using John Van's Hose spreadsheet and replacing the 754.dats with 4-4cyli.dats of the correct length and diameter. --Bram Bram Lambrecht / o o \ BramL@juno.com (...) (25 years ago, 29-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: mars colony - team transport [DAT]
|
|
(...) your wish is my command! this is how the model was originally built anyway (photos and instruction pages will show up on my page in the next couple of weeks). ---...--- 0 Team Transport - 6899 Nebula Outpost Alternate 0 Name: TEAMTRAN.DAT 0 (...) (25 years ago, 29-Jul-99, to lugnet.cad.dat.models)
|
| |
| | Re: mars colony - team transport
|
|
(...) hi sproat thanks for the praise...my only wish is that someday we'll see the panel pieces in yellow and cockpit pieces in charcoal grey so i can make the model in the real world. ..joseph g (25 years ago, 29-Jul-99, to lugnet.cad.dat.models)
|
| |
| | Re: Part number needed & New primitive submission
|
|
(...) I realize that primitives which are sized to 1LDU are easier to use, but a set of primitives which don't all use the same sizing are *harder* to use overall, because the author has to remember which sizing to use for which primitives. Steve (25 years ago, 29-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Re: Uk Technic Box
|
|
What is a "Uk Technic Box" (25 years ago, 29-Jul-99, to lugnet.loc.uk, lugnet.market.jambalaya)
|
| |
| | Re: 12 V Trains on 9V Track
|
|
Can that be done all 12Volt trains? -- Please reply on medwards@ukonline.co.uk Home of the UK Technic Club Magazine Web site: (URL) models and going up Jonathan Wilson <wilsonj@xoommail.com> wrote in message news:37A03CE8.B819ED...ail.com... (...) (...) (25 years ago, 29-Jul-99, to lugnet.trains)
|
| |
| | Re: Part number needed & New primitive submission
|
|
(...) But this piece is more akin to 3855 1x4x3 Window Glass than 3854 1x2x3 Window Pane. This piece and 3855 are akin in that, while they can be rotated, it is *much* less common than sitting vertical in the frame. Your piece, in its current form, (...) (25 years ago, 29-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Re: Reading Serial Port
|
|
It isn't hanging, it's a blocking read until it recieves some specified number of characters. You can use a non blocking read by specifying O_NONBLOCK, in which case read() will return immediately. The Linux serial programming HOWTO is very good, I (...) (25 years ago, 29-Jul-99, to lugnet.robotics.handyboard)
|
