 | | PWM and encoder
|
|
Hi, i have some questions about PWM and encoder. I made following tests: 1) Speed : motor(0,100) my encoder count f.e. 20clicks / per second 2) Speed: motor(0,50) my encoder count f.e. 15clicks / per second 3) Speed: motor(0,40) my encoder count (...) (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: IR Transmit ?!? HELP
|
|
(...) Did you follow the instructions in the HB Assembly debug? at (URL) says: Output Stage If LED9R fails to light after the poke command is issued, trace the following progression of signals. Please refer to the infrared output schematic: * 6811 (...) (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | IR Transmit ?!? HELP
|
|
I recently assembled a Handy Board, everything is perfect except for the IR Transmitter. The IR Tx LED does not light. It is not the LED itself because I replaced it. I can't seem to figre out what's wrong. Please help. Thank You Peter Eacmen (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | To Prof. Fred Martin: Neat!
|
|
Hi, I saw your robot at the Trinity fire fighting contest last Sunday. It was neat, and very animate. I was curious to know if you had figured out why it did what it did during your first run (?). And, what type of sensor were you using on the rear (...) (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Help!! Polaroid problem!!!
|
|
Why does it seem like everyone except me needs a pullup resistor and perhaps a capacitor somewhere to operate the Polaroid? I've never had any problems without any of these components. ??? The first time I connected the sensor, it worked perfectly. (...) (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | tsl1301 or 1401
|
|
Has anyone tried to use one of the TI tsl1301 or 1401 linear sensors with the HB. I ended up with a few but am having a tough time trying to figure out what the data sheets are trying to tell me. Not real clear (to me). Bruce A. Moore (26 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Handy board help
|
|
I am interested in using the Handy Board, but I have a few questions about it first. Please help. :) I noticed the Handy Board supports 4 motors but I am interested in using stepper motors with it. Is this possible? If so what modifications would be (...) (26 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Help!! Polaroid problem!!!
|
|
Are you using a pullup resistor on the ECHO pin? If not that is your problem. The ECHO output is an open collector driver which requires an 4.7 K pull-up resistor between the output and Vcc. The pull-up is necessary for connecting the module to a (...) (26 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Help!! Polaroid problem!!!
|
|
I am trying to use one of the Polaroid 6500 kits from Wirz with my senior design project. It doesn't exactly use a handyboard, but our microcontroller is virtually identical at the lowest level. The problem is when we attach the device to the scope, (...) (26 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | is IC compatible with the MC68HC11F1
|
|
hi from France, I already have a handy-board running with a 11A1 chip and I plan to adapt the circuit for a 11F1 chip, with the same memory map. Does someone have any experience about running IC with this chip? Will it work with the pcode_hb.s19 (...) (26 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
|
