 | | RE: Low battery detection
|
|
Can you translate this into "EE for dummies?". I slowly start to grasp some of the idea about voltage dividers but still don't understand. Won't this setup drain the battery? How does one calculate and wire such a thing - in this particular case? I (...) (27 years ago, 17-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Power
|
|
Perhaps your motors draw too much current. You can only draw 600mA from the L293D driver IC. In the HB manual, you can see you can draw 1A from a IC from TI. (I don't know the exact number right now). You could try to use a seperate IC for each (...) (27 years ago, 17-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Power
|
|
Perhaps the problem is your motor-drivers IC's. If you use the L293D or something, which are standard on the HandyBoard, you can only draw abou 600 mA. I use the other ones mentioned in the HB manual (they're from Texas Intr., but I can't remember (...) (27 years ago, 17-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Power
|
|
Perhaps the problem is your motor-drivers IC's. If you use the L293D or something, which are standard on the HandyBoard, you can only draw abou 600 mA. I use the other ones mentioned in the HB manual (they're from Texas Intr., but I can't remember (...) (27 years ago, 17-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Power
|
|
Hello everyone. I finally got everything cool with the Handyboard I'm using in terms of the software and loading it and getting all connections right. The only problem now is that the motors on my little robot pretty much stop after maybe 45 seconds (...) (27 years ago, 17-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Disconnections etc.
|
|
I have a few problems with the Handyboard I just put together: 1. I lose contact with the board from IC very often. Then, when I try to reset the board it will not always reboot. One of the following usually happens: a) I just get the single line of (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | An answer from Polaroid
|
|
A while back I asked if anyone knew about a socket to accomodate the 9-pin plugs that come with the Polaroid sonar modules. I feel pretty dumb now, because I talked with the people at Polaroid, who tell me that it's not really a plug at all; it's (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Re: How i can beep the handy in Imgecraft C....
|
|
Hi German, I sent this to you before, but I guess you didn't keep it. This one is going to both the robot-board and handyboard lists you can always find it again later by searching the archives for these lists. To beep the beeper using ImageCraft C (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Re: pneumatics
|
|
(...) Small pneumatics are tough because commercial actuators are (A) expensive and (B)they assume a stationary machine tied to "shop air", i.e. miniature mobile compressors/regulato.../receivers are nonexistant. HOWEVER; you still have 3 good (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Gear Motors
|
|
(...) Check out Herbach and Rademan at www.herbach.com for surplus DC gearhead motors. They often have 6-24 volt, optically encoded motors for $20-$25 each. J.V. -- ***...*** * John Vaughn Phone: 315-781-3906 * * Dept. of Math & Computer Science (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
