| | Re: Re[2]: IR Collision avoidance
|
|
Richard, I've tried the op-amp method and had some success. I just don't know how I would power the -5V via the HB. Do you have any suggestions? Thanks. (...) (28 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
|
| | Re[2]: IR Collision avoidance
|
|
Bill, Why is everyone using a digital device to try to detect the (analogue) distance to an object? Especially one with AGC, it makes no sense! I modulated the IR at 10KHz (high enough to be away from mains light flicker, but out of the way of the (...) (28 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
|
| | Re: IR Collision avoidance
|
|
Well, at risk of being branded a heretic, since you've brought up the issue of modulated IR, I'm going to throw out an observation I've made about the Radio Shack IR sensors which several other people on the mailing list have privately disagreed (...) (28 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
|
| | phone cord length
|
|
Hi, I was wondering how long a piece of cable you can put between the handboard and the serial interface and still have it work. If anyone has any experience with this please email me... thanks, -Jeremy ___...___ Jeremy Green jag@world.std.com (...) (28 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
|
| | Re: IR Collision avoidance
|
|
(...) I have a few questions for you. How did you combine the 38khz and 500hz signal. In a design that I am working on now I have two signals similar to yours and an enable signal running into a three input AND gate. I haven't built it yet but it (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
|
| | motors
|
|
Hi, Yes, that schematic posted by Prabal was exactly what I meant. I sent you the bmp anyway, Adam. David (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
|
| | Re: motor voltages
|
|
Adam, I think David meant something like this: |---|<|---|<|---|<|---| M+ ----x x----(motor)---- |---|>|---|>|---|>|---| | | M- ---...--- That way you have a voltage drop AND conduction in both directions. - Prabal (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
|
| | where to get a board.
|
|
hello. i'm new to this mailing list, and would like to purchase a handy board. i'm curious if there i a place where i could perhaps find a used one (in working order), or who the best (read: cheapest) distributor is. thanks for info you can provide. (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
|
| | Re: Servos and Handyboard.
|
|
you can't power 2 servos from the hb's own +5v supply. get a separate 5v supply (linear regulated, *noT* a switching supply, OR batteries) and run your servo power from that. connect this external supply ground to the HB motor ground (on J13). -Fred (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
|
| | Re: motor voltages
|
|
David, I would be interested in seeing a schematic on the wiring of the diode array. I am not sure of how it goes - exactly. I'm not located near a dedicated fax. I was wondering if it might not be too much trouble to sketch the schemtic on some (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|