 | | UNSUBSCRIBE from handyboard@media.mit.edu
|
|
Hello, who can tell me how I UNSUBSCRIBE me from this Mailing List... Thanks Bye, Matthias Pletz (28 years ago, 13-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | Re[2]: as11_ic
|
|
Hello, Am I the only one who is still lost with this stuff? Help! I see the Mac ports of the as11 assembler on the web site; why can't the DOS version be put there? I have been unable to find the assembler on Motorola's web site despite several (...) (28 years ago, 13-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | is there a program
|
|
I am building a handyboard from the board up and i was wondering if a program exists that when the handyboard is programmed i can get it to run through a maze on my monitor, i can't afford a body right now thanks ted houle (28 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | Re: as11_ic
|
|
There are two fundamentally different ways to go about writing assembly language programs for the Handy Board: 1. Write them as callable functions for the Interactive C environment, using the as11_ic program. 2. Scrap Interactive C entirely, and (...) (28 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | as11_ic
|
|
Hi, I was wondering if there is a version of the as11_ic assembler available for the IBM PC. If not, is there any other way to use an .asm file on the handy board? Thanks. -LUKE (28 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | Building new PCODE
|
|
As I cant seem to get a 16x2 LCD, I have installed a 16x1 display. The problem now is building a suitable version of the PCODE to support it without workarounds. I don't have a unix box so I got Kent's (?) port to the PC. That, however, is an older (...) (28 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Signal Diode
|
|
JTW, Use 1n4002, 1n4004, etc - they are higher rated parts and usually the same price (which is why 1n4001 has been discontinued - everybody upgraded for free!). Richard ___...___ Reply Separator ___...___ Subject: Signal Diode Author: (...) (28 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | as11_ic
|
|
Hi, I was wondering if there is a version of the as11_ic assembler available for the IBM PC. If not, is there any other way to use an .asm file on the handy board? Thanks. -LUKE (28 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | sonar&motor driver
|
|
Hello everyone, If the polaroid sonar sensors are connected as mentioned by kent (ftp site), is it still possible to use motor ports 2 & 3? (28 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Signal Diode
|
|
The 1N4001 is the 50v version of a family of diodes (1N4001-1N4007) that cover 50 volts to 1000 volts. In general you could use any of the other versions. I would recommend looking for 1N4002(100v) or 1N4003(200v). As it happens Digikey says they (...) (28 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
|
