|
The 8889 Technic Ideas book has four pages dedicated to a six-wheeled truck,
which appears to be built largely from a combination of 8859 and 8860.
Unfortunately it fails to give instructions, and all the pictures are from one
side, leaving much of the underneath and far side a mystery.
I attempted to build this once as a kid, but didn't get very far - as I didn't
have 8859 I was probably doomed to failure. I still don't have 8859, but a few
years ago I decided I probably had most of the necessary parts and attempted to
build it. There are a small number of part substitutions (notably blue 16 long
technic beams being replaced with black ones), and obviously what is not
illustrated in the book is conjectural, while attempting to be stylistically
appropriate. I've also added four extra 1x4 technic beams to tie together the
upper and lower members of the chassis about the mid-point of its length, as the
original design had a notable weak point here.
Otherwise the design works well. The V6 engine runs smoothly, and the gears
work about as well as that method of gears could work, although I think there
was some modification to the gearing in front of the gearbox as the pictures
showed a system that wouldn't work (or ended up with two ways of getting the
same gearing). The system has three forward speeds (and no reverse) but the
gearing is split fore and aft of the gear stick. The rear wheel lifting
mechanism works well.
The model isn't as robust as the Technic sets of the time, although it seemed to
survive several young children playing with it on Thursday, which was when I had
the opportunity to photograph it. I think I built it in about 2004, but I
couldn't swear to that.
Original pictures are pages 38-41 of 8889, which for those of you whose parents
didn't buy it for £2.89 from the Jolly Giant, can be found here:
http://www.peeron.com/scans/8889-1/
My version of it can be seen here:
http://www.brickshelf.com/cgi-bin/gallery.cgi?f=237779
Let me know what you think, and if anyone else has attempted to recreate this.
Al
|
|
|
I have the 8889 book, and looking closely at your photos and the book's I
couldn't find even one tiny difference. (Apart fromt he blue beam you mentioned
but that doesn't count). It's THAT good.
Since you already experienced the anguish of seeing photos of that beautiful
model but not having instructions on how to build it, maybe you could relieve us
and provide step by step instructions yourself ;)
|
|
|
dear al
have you ever constructed a (portable) forklift or do you know anyone that has?
christian
|
|
|
Stephane Simard wrote:
> I have the 8889 book, and looking closely at your photos and the book's I
> couldn't find even one tiny difference. (Apart fromt he blue beam you mentioned
> but that doesn't count). It's THAT good.
>
> Since you already experienced the anguish of seeing photos of that beautiful
> model but not having instructions on how to build it, maybe you could relieve us
> and provide step by step instructions yourself ;)
Sorry for the delay in replying. I will add it to my long term list of
things to do, but please don't expect it any time soon! Could be years,
unfortunately.
Al
|
|
|
christian wrote:
> dear al
>
> have you ever constructed a (portable) forklift or do you know anyone that has?
>
> christian
No, sorry, I'm not exactly sure what you mean, but not me, nor do I know
anyone who has aside from the standard LEGO models.
Al
|
|
|
In lugnet.technic, Alastair Disley wrote:
> christian wrote:
> > dear al
> >
> > have you ever constructed a (portable) forklift or do you know anyone that has?
> >
> > christian
>
> No, sorry, I'm not exactly sure what you mean, but not me, nor do I know
> anyone who has aside from the standard LEGO models.
>
> Al
I started a 9th scale forklift in 2003 using a Bimba piston but never finished
it. Although those pistons may be expensive and hard to get, they double your
possibilities with lifting designs.
http://bimba.com/
The one I have extends 20 cm, which along with a single- pulley chain system
would allow for a 40cm max height.
This fella is getting off to a flying start with a design.
http://www.brickshelf.com/cgi-bin/gallery.cgi?f=241722
|
|
|
In lugnet.technic, Nathan Bell wrote:
> In lugnet.technic, Alastair Disley wrote:
> > christian wrote:
> > > dear al
> > >
> > > have you ever constructed a (portable) forklift or do you know anyone that has?
> > >
> > > christian
> >
> > No, sorry, I'm not exactly sure what you mean, but not me, nor do I know
> > anyone who has aside from the standard LEGO models.
> >
> > Al
>
> I started a 9th scale forklift in 2003 using a Bimba piston but never finished
> it. Although those pistons may be expensive and hard to get, they double your
> possibilities with lifting designs.
>
> http://bimba.com/
>
> The one I have extends 20 cm, which along with a single- pulley chain system
> would allow for a 40cm max height.
>
> This fella is getting off to a flying start with a design.
>
> http://www.brickshelf.com/cgi-bin/gallery.cgi?f=241722
hi nathan
nice forklift - would it be possible to mount it onto a lorry?
|
|
|
In lugnet.technic, Christian Fabsich wrote:
> In lugnet.technic, Nathan Bell wrote:
> > In lugnet.technic, Alastair Disley wrote:
> > > christian wrote:
> > > > dear al
> > > >
> > > > have you ever constructed a (portable) forklift or do you know anyone that has?
> > > >
> > > > christian
> > >
> > > No, sorry, I'm not exactly sure what you mean, but not me, nor do I know
> > > anyone who has aside from the standard LEGO models.
> > >
> > > Al
> >
> > I started a 9th scale forklift in 2003 using a Bimba piston but never finished
> > it. Although those pistons may be expensive and hard to get, they double your
> > possibilities with lifting designs.
> >
> > http://bimba.com/
> >
> > The one I have extends 20 cm, which along with a single- pulley chain system
> > would allow for a 40cm max height.
> >
> > This fella is getting off to a flying start with a design.
> >
> > http://www.brickshelf.com/cgi-bin/gallery.cgi?f=241722
>
> hi nathan
>
> nice forklift - would it be possible to mount it onto a lorry?
The forklift I posted is not my design. "TT" from brickshelf did that. It was
just to give you ideas, and is closer to 1/16th scale. Maybe you can find his
email and get some ideas from him. My only idea is to use Bimba pneumatics.
|
|
|
In lugnet.technic, Alastair Disley wrote:
|
The 8889 Technic Ideas book has four pages dedicated to a six-wheeled truck,
which appears to be built largely from a combination of 8859 and 8860.
Unfortunately it fails to give instructions, and all the pictures are from one
side, leaving much of the underneath and far side a mystery.
|
When my parents gave me this book in the mid 80s I wanted to build this truck.
Just like you I only had the 8860 car chassis and I bought a used 8859 in ´95.
But in the second half of the 80s I used the boogie lift for two of my truck
models which are shown below. While original trucks have double mounted wheels
at the back I copied the system 1:1 as I thought it worked properly. But then I
discovered the same issues you did while I figured out the rest of the truck
myself.
Nice to see someone has built the original one from the book :)
Dennis Bosman
www.dennisbosman.nl
|
|
|