To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.robotics.rcx.pbforthOpen lugnet.robotics.rcx.pbforth in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / RCX / pbFORTH / *638 (-10)
  Re: Help - no response from "brick"
 
(...) This old post may be useful to the people out there who are trying to use pbForth with BricxCC. (URL) bitmap is missing but it didn't contain any really useful information. The most important thing to remember about BricxCC and pbForth is to (...) (20 years ago, 18-Oct-04, to lugnet.robotics.rcx.pbforth)
 
  Re: Help - no response from "brick"
 
(...) ---...--- Thanks for your response. It, along with Parick's posting of 9 April enabled me to get started. Jordon (20 years ago, 15-Oct-04, to lugnet.robotics.rcx.pbforth)
 
  Re: Getting started; FFT; millisecond timing
 
Thanks for your posting of 9 April 2004. It was very useful. Jordon (20 years ago, 15-Oct-04, to lugnet.robotics.rcx.pbforth)
 
  Re: Help - no response from "brick"
 
(...) I don't know the answer, but I know a workaround: use Bricxcc's pbForth console. see (URL) (20 years ago, 14-Oct-04, to lugnet.robotics.rcx.pbforth)
 
  Help - no response from "brick"
 
I used nqc to download pbforth.srec. (The LCD displays "4th".) There is no response from the "brick" using either HyperTerm or CRT4.1. I'm using RCX1.0. Am I missing something? Thanks, Jordon (20 years ago, 13-Oct-04, to lugnet.robotics.rcx.pbforth)
 
  Re: Getting started; FFT; millisecond timing
 
(...) Thanks, Patrick. I just took the plunge into pbForth and I was stuck. After downloading the firmware, I couldn't get Ralph's console nor Hyperterminal to give me an "OK" response. I couldn't figure out how to get to the Bricxcc pbForth (...) (20 years ago, 10-Oct-04, to lugnet.robotics.rcx.pbforth)
 
  RE: Pbforth probs
 
Did you upload the pbforth_servo.srec file? (...) (20 years ago, 22-Jul-04, to lugnet.robotics.rcx.pbforth)
 
  Re: Pbforth probs
 
(...) The fact is that nothing happens! Servo doesn't move (the interface works well with NQC) Or the console says "ABORTED etc..." What's wrong? (20 years ago, 22-Jul-04, to lugnet.robotics.rcx.pbforth)
 
  RE: Pbforth probs
 
Sorry, the page IS unclear. 0 1 0 SERVO_SET will center the servo on the first motor port 50 1 0 SERVO SET wil moove it in one direction 100 1 0 SERVO_SET will move it more in one direction -50 1 0 SERVO_SET will move it in the other direction -100 (...) (20 years ago, 22-Jul-04, to lugnet.robotics.rcx.pbforth)
 
  Pbforth probs
 
Hi. After reading the web pages, word lists, help, tutorials, I still wonder how to control SERVO MOTORS with PBForth. I tried the SERVO_SET command but it says "ABORTED (missing ;?)" What does it mean?How can I interprete the syntax explained on (...) (20 years ago, 22-Jul-04, to lugnet.robotics.rcx.pbforth)


Next Page:  5 more | 10 more | 20 more

Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR