 | | Re: Building a three-foot bridge
|
|
Brian, Here's my znap bridge I did. It's pretty sturdy, albeit somewhat heavy as well due to the amount of plates I used on the base.. It's a double 6-wide train bridge. The trick that I did was using the 2x2 brick and half stud pieces combined with (...) (22 years ago, 24-Jan-03, to lugnet.trains, lugnet.znap)
|
| |
| | Re: Building a three-foot bridge
|
|
"Cary Clark" <cary@corp.nospamwebtv.net> wrote in message news:H96p3M.I6q@lugnet.com... (...) run (...) Here are a couple of pictures of the ZNAP bridges Cary built along with one I built. (URL) built the two bridges that cary the trains across the (...) (22 years ago, 24-Jan-03, to lugnet.trains, lugnet.znap)
|
| |
| | Re: Building a three-foot bridge
|
|
(...) Well, Brian, I can say one of my 60 inch long ZNAP bridge twisted and collapse at a train show, with the GFLTC (no pics). Two trains fell 30+ inches to the ground out side in the dirt! The best bet for a ZNAP bridge is to support the track on (...) (22 years ago, 24-Jan-03, to lugnet.trains, lugnet.znap)
|
| |
| | Re: Building a three-foot bridge
|
|
(...) Well there's Wayne Hussey's bridge which was built out of znap (URL) it's a bit longer than you need, but I imagine it would've been impossible to use if it had a twisting problem. Maybe you could adapt his deck construction technique? Also I (...) (22 years ago, 24-Jan-03, to lugnet.trains, lugnet.znap)
|
| |
| | Re: Building a three-foot bridge
|
|
Here is one photo of my lift bridge that has a 32" span (approximately): (URL) holds up very well, and i assume that you could make it even longer if you needed to. -Rob www.cei.net/~rhendrix/lego.html www.msltc.org "Brian Kendig" (...) (22 years ago, 23-Jan-03, to lugnet.trains, lugnet.znap)
|
| |
| | Re: Building a three-foot bridge
|
|
(...) ... Brian: I've built some ZNAP and Technic bridges of similar lengths but haven't run into the twisting problem. Any chance you can post a picture of what you have? That would help a lot. Cary (22 years ago, 23-Jan-03, to lugnet.trains, lugnet.znap)
|
| |
| | Building a three-foot bridge
|
|
I want to build a bridge to cross a one-meter gap between two train platforms. The bridge must hold two straight lengths of track, spaced with one trackwidth between them (the distance there would be if you snapped two cross-intersection track (...) (22 years ago, 23-Jan-03, to lugnet.trains, lugnet.znap)
|
| |
| | Loads of Znap available if anyone is interested
|
|
This all comes from a collection we bought out, where we are mostly interested in the sets, and not the Duplo/Znap/Buckets/B...ic/Creator stuff that was also collected. So we assigned a relatively low "value" to these portions of the collection but (...) (22 years ago, 15-Sep-02, to lugnet.znap)
|
| |
| | connector numbers
|
|
do the connecters have numbers yet? -grey with technic hole and two pins -purple with znap hole and four pins -black and yellow movable with four pins and the short beam with one hole x (23 years ago, 23-Feb-02, to lugnet.znap)
|
| |
| | Re: Interfacing Znap to System
|
|
(...) You should look around Brickshelf.com, someone was working on a monorail system using Znap as the rail. Perhaps you could intergrate the track and the bridge's topmost strut into one Znap thing-bob. Aaron (23 years ago, 13-Feb-02, to lugnet.znap)
|
