 | | Re: Help Open 12v switch track motor- doesn't switch —James Mathis
|
| | | Ben, Thanks. Any assistance you can provide will be greatly appreciated. However, I would not want you to re-open a repaired points motor that currently works and risk damaging the box. Perhaps Ludo would be willing to speak to this again? I am (...) (25 years ago, 16-May-00, to lugnet.trains)
|
| | | |
| | | | | Re: Help Open 12v switch track motor- doesn't switch —Reinhard "Ben" Beneke
|
| | | | (...) Dear James (and whoever might be interested in this also), I took the point motor from Ludo and opened it again (was hardly glued now). And I took a few pictures to put the best of them on my homepage here: (URL) direct picture link here: (...) (25 years ago, 16-May-00, to lugnet.trains)
|
| | | | |
| | | | | | Re: Help Open 12v switch track motor- doesn't switch —James Mathis
|
| | | | | Thank you for the photograph of the opened gray motorized points box, Ben. What a task to open that box! Which sides of the gray box were glued together? - the long sides or the short sides? Thanks. later, James Mathis (...) (25 years ago, 16-May-00, to lugnet.trains)
|
| | | | | |
| | | | | | | Re: Help Open 12v switch track motor- doesn't switch —Reinhard "Ben" Beneke
|
| | | | | | (...) At least the long sides, but I fear it have been all four sides.... Regards and good night (0:30 am) Ben (25 years ago, 16-May-00, to lugnet.trains)
|
| | | | | | |
| | | | | | | | Re: Help Open 12v switch track motor- doesn't switch —Ludo Soete
|
| | | | | | (...) Hi Folks! It was originally glued on four sides. After opening, i glued it back together with special ABS glue. I found this in a shop where they sell models (airplane, cars,..) Pictures says, in this case, more than words, isn't it? regards, (...) (25 years ago, 17-May-00, to lugnet.trains)
|
| | | | | | |
| | | | | | | | Re: Help Open 12v switch track motor- doesn't switch —James Mathis
|
| | | | | | Hello, Ludo! Thanks VERY much for pioneering this operation for me. I have now fully repaired my 12v motorized track switch box. :-) Very happy it now works. I went home during lunch and soldered the thin coil wire back onto the inside plug (...) (25 years ago, 17-May-00, to lugnet.trains)
|
| | | | | | |
| | | | | | Re: Help Open 12v switch track motor- doesn't switch —James Mathis
|
| | | | After a couple of hours, my 12volt points motor gray box is opened. I damaged the top cover slightly at its base along the flange at one corner. The damage is a flex/cut through the flange caused by too strong of a cut into the very small gap (...) (25 years ago, 17-May-00, to lugnet.trains)
|
| | | | |
| | | | | | Re: Help Open 12v switch track motor- doesn't switch —James Powell
|
| | | | (...) _small_ iron, using low melt solder, and lots of flux. I use a Antax 18W, 12V iron (but, it is british, so you are not likely to be able to get one). Otherwise, a Temp. Controlled iron, or run a small (25W) iron using a Variac (Variable (...) (25 years ago, 17-May-00, to lugnet.trains)
|
| | | | |
| | | | | | Re: Help Open 12v switch track motor- doesn't switch —James Mathis
|
| | | | Thanks, James! I'll try to get this hooked up tonight. Melting the plastic is a concern. We'll see if I'm worthy. Thanks for the advice. later, James Mathis (...) to (...) (25 years ago, 17-May-00, to lugnet.trains)
|
| | | | |
