|
|
 | | Re: "Big Blue" Pneumatic 4-6-4 engine and tender
|
| (...) It isn't the strongest, bot for this application, it keeps the cylinders in direct line with the push rods, so it works. It has the added benefit of keeping the pneumatic tubes more securely fastened to the input/output ports on the cylinder (...) (18 years ago, 30-Oct-06, to lugnet.org.ca.rtltoronto, lugnet.trains, FTX)
| | | | | Re: "Big Blue" Pneumatic 4-6-4 engine and tender
|
| (...) Hey David, very awesome! :-) I especially like the way you've secured the cylinders, is it strong? Also, pretty neat idea to stop the air at the front using the lever stick. About the slipping, how about putting rubber bands on the driver (...) (18 years ago, 30-Oct-06, to lugnet.org.ca.rtltoronto, lugnet.trains, FTX)
| | | | | Re: Stolen flatcar with a stolen load
|
| (...) A Trolley, yes. (URL) The Neighborhood Trolley>, in fact. If you look behind the little train station (URL) here>, you can barely make out the other touch sensor at the other end. These are our subway modules which have been been so far too (...) (18 years ago, 29-Oct-06, to lugnet.trains, FTX)
| | | | | Re: Stolen flatcar with a stolen load
|
| (...) Is that touch sensor below the stop sign to control a trolley or similar? I found (URL) this> pic which shows the scene a bit better. tim (18 years ago, 29-Oct-06, to lugnet.trains, FTX)
| | | | | Re: Stolen flatcar with a stolen load
|
| (...) (URL) Among others>:-) (URL) JOHN (18 years ago, 28-Oct-06, to lugnet.trains, FTX)
| | | | | Stolen flatcar with a stolen load
|
| (URL) Flatcar design by Didier Enjary, brick design by Benn Coifman. --Tony (18 years ago, 28-Oct-06, to lugnet.trains, lugnet.general, FTX)
| | | | | Re: A few train MOCs
|
| (...) The news that inspired my building was of tank cars in Deerfield, MA (USA). Reportedly that train was carrying vegetable oils and grains. I know that same rail line carries a lot of coal. But I think most fuel oils in my region are brought in (...) (18 years ago, 28-Oct-06, to lugnet.trains)
| | | | | Re: The inevitable leap into 10-Wide Trains...
|
| (...) Yes, I remembered, but just after posting! (why does this happen? - I must need more sleep to help my memory!) :-) Dan, it's particularly good that your kit fits with the larger scale, and you managed to get it through the design and (...) (18 years ago, 28-Oct-06, to lugnet.trains, FTX)
| | | | | Re: "Big Blue" Pneumatic 4-6-4 engine and tender
|
| In lugnet.org.ca.rtltoronto, Ben Fleskes wrote: <snip> (...) A huge oversite on my part-- Ben, I know I've thanked you before, but seriously, again thanks for the wheel sets that you produce--without them, my pneumatic train wouldn't have happened, (...) (18 years ago, 27-Oct-06, to lugnet.org.ca.rtltoronto, lugnet.trains)
| | | | | Re: "Big Blue" Pneumatic 4-6-4 engine and tender
|
| (...) Yep--did the 90 degree offset--when you watch the video, you can see the wheels pause 4 times per revolution (using compass points-- NE, SE, SW, NW)--that's when one phase is done and waiting for the next phase. 4 phases with two pistons! I (...) (18 years ago, 27-Oct-06, to lugnet.org.ca.rtltoronto, lugnet.trains)
|
|
