 | | New train MOC - 0-6-0+0-6-0 Beyer-Garratt locomotive
|
|
I finally got around to doing some building. I've been doing a bit of tossing around in my mind a Beyer-Garratt after seeing the My Own Train engines. I've also been figuring out what passenger cars I will be making as I've been collecting train (...) (23 years ago, 26-Jan-02, to lugnet.trains, lugnet.announce.moc)
|
| |
| | Re: Unused Parts in Small Loco 3740
|
|
(...) If you are referring to a black 1x2 plate with handle then I am using over 120 of them on a bridge project I am constructing presently. -Rob (23 years ago, 26-Jan-02, to lugnet.trains)
|
| |
| | Unused Parts in Small Loco 3740
|
|
Has anyone found a useful purpose for the 4 black plates 1 x 2 with handles (Type 2) part number 3839b which are included in the small loco set 3740. They are not used in either of the two engine designs of this set as detailed in the instruction (...) (23 years ago, 26-Jan-02, to lugnet.trains)
|
| |
| | Re: Point Motor Instructions
|
|
(...) What does the lever engage? How easy is it to tell when the turnout is at the right location? I can see the value of building at least a couple of these for our show layout. Our layout had one turnout which was basically impossible to reach (...) (23 years ago, 26-Jan-02, to lugnet.trains)
|
| |
| | Re: Gear and Axle Strength (was Re: Power Pullin' With My Tractor)
|
|
(...) Has anyone tried making an axle of 2x2 round bricks with bearings made from 1x4 arch bricks? I just played with it a little and it looks like the bearing would work ok. You could also make a bearing from macaroni bricks, but I think it would (...) (23 years ago, 26-Jan-02, to lugnet.trains, lugnet.technic)
|
| |
| | Point Motor Instructions
|
|
Hi folks, I still occasionally get requests for information on my old automatic point motor. Well, I've long since moved to a more compact and reliable model, and after the rtlToronto Train3 show last weekend, I've decided to post the instructions (...) (23 years ago, 25-Jan-02, to lugnet.org.ca.rtltoronto, lugnet.trains)
|
| |
| | Gear and Axle Strength (was Re: Power Pullin' With My Tractor)
|
|
(...) That sounds like a very good solution. My solution to preventing axle shear has been to create multiple shear planes (like the hinges of the boom on my crawler crane). The problem is that it takes up a lot of room and there can be a lot of (...) (23 years ago, 25-Jan-02, to lugnet.trains, lugnet.technic)
|
| |
| | Re: Power Pullin' With My Tractor
|
|
In lugnet.technic, Thomas Avery writes: Thanks for the update! (...) Long long ago, when I first got into the hobby, I was corresponding with John Gerlach about lift bridges and he reported axle failures, but it was due to shear rather than torque. (...) (23 years ago, 25-Jan-02, to lugnet.technic, lugnet.trains)
|
| |
| | Re: Train Level Crossing Gate 815 Variation
|
|
(...) parts. Are you planning on pointing out the variations of basic bricks? A 2x4 brick has gone through at least 4 different designs, and likely there are more that I can't think of offhand. Also, I think that you are missing another variant of (...) (23 years ago, 25-Jan-02, to lugnet.trains)
|
| |
| | Re: Cass #5
|
|
There are quite a few good pictures at the Cass Railroad Site www.cassrailroad.com The cass scenic railroad has several shays, a climax and a hiesler. The web site has pictures of most of thier engines. There is also several books out on cass' (...) (23 years ago, 25-Jan-02, to lugnet.trains)
|
