 | | Re: 9V train collection completed
|
|
(...) come (...) Ben, are you SURE you have all the 9v sets after this deal? I mean ALL the real 9v sets plus ALL the fake ones? Jon (24 years ago, 18-May-00, to lugnet.trains)
|
| |
| | Re: 3225 Classic Train engine
|
|
(...) Hello Ryan. The 3225 Locomotive has generated a lot of derision on LUGNET but I actually like it partly beause it is Lego's only recent attempt at a steam engine. I think it is supposed to represent a typical European shunter (US=Switcher) (...) (24 years ago, 18-May-00, to lugnet.trains)
|
| |
| | Re: New to me- Ludo's trains
|
|
(...) Thanks for the interest. I'm thinking of redo the Belgian locomotive. Same color sheme but 1 brick less high. He can't pass under my bridge !! The model is created with MLCAD and the .dat file is available at my site. Now i'm working on the (...) (24 years ago, 18-May-00, to lugnet.trains)
|
| |
| | Re: New to me- Ludo's trains
|
|
Ludo's web site: (Sorry) (...) must (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | New to me- Ludo's trains
|
|
I do try to catch all the train stuff that comes through this group, but I must have missed your site, Ludo. So wonderful to see more train models, as I just a few days ago saw your web site again. I don't recall having seen the two locomotives (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
Hello, Ludo! Thanks VERY much for pioneering this operation for me. I have now fully repaired my 12v motorized track switch box. :-) Very happy it now works. I went home during lunch and soldered the thin coil wire back onto the inside plug (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
(...) Hi Folks! It was originally glued on four sides. After opening, i glued it back together with special ABS glue. I found this in a shop where they sell models (airplane, cars,..) Pictures says, in this case, more than words, isn't it? regards, (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Question about Running 12v trains
|
|
(...) One possible explanation for this (since I have washed many bricks and noticed this sometimes, but not most of the time): Dirty bricks will have a layer of grit on them which could throw off the tolerances, and will increase wear, especially (...) (24 years ago, 17-May-00, to lugnet.trains, lugnet.boats, lugnet.general)
|
| |
| | Re: Question about Running 12v trains
|
|
(...) first (...) 4.5V (...) At the age of maybe 5 to 7 I built a paddle steamer too, but I used the red swimming hulls of set 311: (URL) I built it with a gap in the middle for the paddles shaft and placed my 103 motor avove that. (I dared to use (...) (24 years ago, 17-May-00, to lugnet.trains, lugnet.boats)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
Thanks, James! I'll try to get this hooked up tonight. Melting the plastic is a concern. We'll see if I'm worthy. Thanks for the advice. later, James Mathis (...) to (...) (24 years ago, 17-May-00, to lugnet.trains)
|
