 | | Re: Help Open 12v switch track motor- doesn't switch
|
|
Hello, Ludo! Thanks VERY much for pioneering this operation for me. I have now fully repaired my 12v motorized track switch box. :-) Very happy it now works. I went home during lunch and soldered the thin coil wire back onto the inside plug (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
(...) Hi Folks! It was originally glued on four sides. After opening, i glued it back together with special ABS glue. I found this in a shop where they sell models (airplane, cars,..) Pictures says, in this case, more than words, isn't it? regards, (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Question about Running 12v trains
|
|
(...) One possible explanation for this (since I have washed many bricks and noticed this sometimes, but not most of the time): Dirty bricks will have a layer of grit on them which could throw off the tolerances, and will increase wear, especially (...) (24 years ago, 17-May-00, to lugnet.trains, lugnet.boats, lugnet.general)
|
| |
| | Re: Question about Running 12v trains
|
|
(...) first (...) 4.5V (...) At the age of maybe 5 to 7 I built a paddle steamer too, but I used the red swimming hulls of set 311: (URL) I built it with a gap in the middle for the paddles shaft and placed my 103 motor avove that. (I dared to use (...) (24 years ago, 17-May-00, to lugnet.trains, lugnet.boats)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
Thanks, James! I'll try to get this hooked up tonight. Melting the plastic is a concern. We'll see if I'm worthy. Thanks for the advice. later, James Mathis (...) to (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
(...) _small_ iron, using low melt solder, and lots of flux. I use a Antax 18W, 12V iron (but, it is british, so you are not likely to be able to get one). Otherwise, a Temp. Controlled iron, or run a small (25W) iron using a Variac (Variable (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
After a couple of hours, my 12volt points motor gray box is opened. I damaged the top cover slightly at its base along the flange at one corner. The damage is a flex/cut through the flange caused by too strong of a cut into the very small gap (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Lego layout from the seventies
|
|
(...) See if you can?? You mean try NOT to spot any :-/ That's what got me about 1/2-1 hr with a Model Builder at the LLC Grand Opening weekend - my grousing about all the parts in pink, light blue, green, and brown that just weren't purchasable. I (...) (24 years ago, 17-May-00, to lugnet.general, lugnet.trains)
|
| |
| | Re: Question about Running 12v trains
|
|
(...) Ben, we have _got_ to hear the story of this! I used to make paddle "steamers", using Electical tape and Lego (the tape seals the Lego up quite well...except across the bottom...) I don't have any pic's here, and I doubt there are any at (...) (24 years ago, 16-May-00, to lugnet.trains, lugnet.boats)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
(...) At least the long sides, but I fear it have been all four sides.... Regards and good night (0:30 am) Ben (24 years ago, 16-May-00, to lugnet.trains)
|
