Subject:
|
Re: SSClagorpion
|
Newsgroups:
|
lugnet.technic
|
Date:
|
Mon, 19 Apr 2004 20:03:10 GMT
|
Viewed:
|
9280 times
|
| |
|
|
In lugnet.technic, Kevin L. Clague wrote:
> In lugnet.technic, Steve Hassenplug wrote:
> >
> > Ok, we [plan to] have a sensor on the front foot, and can detect when that is
> > down. So, no more sensors are required.
>
> Actualy we need to sense when it is *up*.
Is *up* the same as "not down"? I was thinking it was, but that may not be the
case.
> >
> > So you said, the forward/backward must be changed while the feet are in the air.
> > We've been thinking of having a touch sensor on the front feet, so it can detect
> > when it goes off an edge (like a table). However, it would not know the surface
> > is not there, until it trys to put the foot down. So, all the feet would be
> > down, and it needs to backup. Can it do that? Or will it need to keep walking
> > a bit?
>
> As soon as you figure out that a foot is up, you can reverse directions. I'll
> have to study the state sequence, because there are two non-weight bearing
> pistons that control the feet, so it might be sufficient to see that they are
> telling the feet to lift. You might need two touch sensors wire-ORed together
> (one for each leg group).
This sounds like we can NOT do the table edge detection stuff, using it's feet.
Imagine you're crawling around on your hands and knees, with your eyes closed.
When you get to the top of a stairway, you put your hand down, and it doesn't
touch the ground.
If I understand you correctly (which doesn't always happen via e-mail) you must
continue to crawl forward, until your other hand and knee are off the ground.
That will be a problem.
It's fine if it can't turn, or switch to moving sideways while all feet are on
the ground, but it really needs to be able to reverse direction.
I suspect the front legs can be a small amount longer, so it will detect the
lack of ground, before the weight is really shifted to the new legs.
Will that work?
Steve
|
|
Message has 2 Replies:
 | | Re: SSClagorpion
|
| (...) I think that you are right, that they are the same thing. (...) Hmmm.... We would need to know two things to determine we'd hit the edge of the table. 1. The foot is down as far as it will go. 2. The down foot is not touching anything. We (...) (21 years ago, 20-Apr-04, to lugnet.technic)
| | | Re: SSClagorpion
|
| (...) Ahh now we are getting somewhere. (...) Hmmm, indeed, or perhaps if we monitor the time it takes for a Leg to hit the ground and then install a logic command that will take action if the leg does not hit the ground in a predetermined amount of (...) (21 years ago, 21-Apr-04, to lugnet.technic)
|
Message is in Reply To:
| | Re: SSClagorpion
|
| (...) Actualy we need to sense when it is *up*. (...) As soon as you figure out that a foot is up, you can reverse directions. I'll have to study the state sequence, because there are two non-weight bearing pistons that control the feet, so it might (...) (21 years ago, 19-Apr-04, to lugnet.technic)
|
300 Messages in This Thread:
(Inline display suppressed due to large size. Click Dots below to view.)
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
