 | | Re: Sprocket for small treads
|
|
Set 8482 Cybermaster has 10 in yellow, along with larger treads to go around them. "Kyle Beatty" <carbunicle@appleogue.net> wrote in message news:GsKnoC.M0B@lugnet.com... (...) (23 years ago, 7-Mar-02, to lugnet.technic)
|
| |
| | Re: SNOT - What's the commotion about?
|
|
(...) Uhm, sorry HoMa was a quick post during lunch .) /Tobbe (URL) (23 years ago, 7-Mar-02, to lugnet.technic)
|
| |
| | Re: SNOT - What's the commotion about?
|
|
(...) <snip> Uh, that's "HoMa". He might not appreciate "HoMo", if you know what I mean. ;-) TJ (23 years ago, 7-Mar-02, to lugnet.technic)
|
| |
| | Re: SNOT - What's the commotion about?
|
|
(...) Here's a pretty good page about SNOT by Holger Matthews (HoMo): (URL) in German but Babelfish can make understandable English out of it (at least to me who knows a tad of German): (URL) (23 years ago, 7-Mar-02, to lugnet.technic)
|
| |
| | Re: Single acting pneumatics with spring return
|
|
(...) How coincidental, but it too struck me that we needed to backtrack as the thread was getting pretty muddled up. It seemed to me that we may not be working on the same assumptions. So here's the re-play... The post that you quoted (URL) in (...) (23 years ago, 7-Mar-02, to lugnet.technic, lugnet.robotics)
|
| |
| | Re: Pneumatic Air Compressor not working. Suggestions needed.
|
|
(...) This is not really true. I think that Boyles gas law is (boy, high school physics was a long time ago): Pressure * Volume = c * Temperature Where c is some constant of proportionality. Plus I think that this assumes some "ideal gas". Real (...) (23 years ago, 7-Mar-02, to lugnet.technic)
|
| |
| | Bionicle Comic #3 Finale Group Shot
|
|
A curiously recursive exercise: For a limited time only I have posed the Toa in their triumphal arrangement from the last panel of the third Bionicle comic. The live webcam view - (URL) source material - (URL) (23 years ago, 7-Mar-02, to lugnet.technic.bionicle)
|
| |
| | Re: "One set" pulling challenge
|
|
(...) Here's the picks (URL) (23 years ago, 6-Mar-02, to lugnet.technic)
|
| |
| | Re: Pneumatic Air Compressor not working. Suggestions needed.
|
|
One more thing that I forgot to mention. If you don't use the full stroke of the pump cylinder when pumping, make sure you position the cylinder so that you "bottom out" when the piston is fully retracted. Air will only flow from the atmosphere into (...) (23 years ago, 6-Mar-02, to lugnet.technic)
|
| |
| | Re: Sprocket for small treads
|
|
(...) outside pages (which is how it sees the above when you click on it) but you can cut and paste the URL into a browser and it should work. (23 years ago, 6-Mar-02, to lugnet.technic)
|
| |
| | Sprocket for small treads
|
|
There are 6 of these sprockets for small treads (part=32089) in set 8538. Are they in any other sets? (URL) (23 years ago, 6-Mar-02, to lugnet.technic)
|
| |
| | Re: New moc: 80% completed Atlas Copco Roc F7cr
|
|
"Tobbe Arnesson" <tnt@arnesson.nu> wrote in message news:3c866a74.296428...net.com... (...) finally (...) how (...) I can always make room for more!!! (...) even (...) To make the cylinders more functional. Right know, I cant lift the boom!! Its (...) (23 years ago, 6-Mar-02, to lugnet.technic)
|
| |
| | Re: Strange parts in Nui-Rama set
|
|
(...) It only occurred to me this morning that this piece is designedto sort out two different sizes of bands. There are two black bands that show up a lot in Bionicles sets and this gizmo fits them both equally well. (23 years ago, 6-Mar-02, to lugnet.technic.bionicle)
|
| |
| | Re: New moc: 80% completed Atlas Copco Roc F7cr
|
|
(...) He, you already have more detail then I've ever had 8-) (...) Vacum? (...) /Tobbe (URL) (23 years ago, 6-Mar-02, to lugnet.technic)
|
| |
| | Re: Strengthening Gears
|
|
A Mecha Shower a day keeps the autocannon bullits flying away. Legomaster (...) (23 years ago, 6-Mar-02, to lugnet.technic)
|
| |
| | Single acting pneumatics with spring return
|
|
Hello again, I think I should have another go at this... I wanted to say "Check this out, I found an interesting application for the old pneumatic cylinders" What it came out sounding like was "Mr. Soh was wrong! Look at me prove him wrong!" Sorry (...) (23 years ago, 6-Mar-02, to lugnet.technic, lugnet.robotics)
|
| |
| | Re: Strengthening Gears
|
|
I hahe been lurking on this conversation for a bit. Here are some random thoughts: Blocks, Gears and Axles use three different materials. By that I mean the are differnet grades of the same material or totally different materials. I lean towards (...) (23 years ago, 6-Mar-02, to lugnet.technic)
|
| |
| | Williams F1
|
|
Heya all, will be the Williams F-1 car produced ? If so, when ? And for which price (cca) will it be saled ? Thanx. Rene (23 years ago, 6-Mar-02, to lugnet.technic)
|
| |
| | Re: Strengthening Gears
|
|
(...) This is just a wild thought, but what if the boiling process doesn't alter the the strength of the material, but helps to reduce stress concentration points? If the gear deforms ever so slightly (i.e. negligible deformation- no change when (...) (23 years ago, 6-Mar-02, to lugnet.technic)
|
| |
| | Re: Pneumatics: the old and the new
|
|
(...) And most other pneumatics systems do too, but its easier if you have a tank in which you have a high pressure (or a low pressure). (23 years ago, 6-Mar-02, to lugnet.technic, lugnet.robotics)
|
