 | | Re: threaded axle
|
|
(...) Not sure, but Doug Carlson has some info on it (something about a 2mm pitch): (URL) you can easily thread a regular axle by using a die. 10-24 and 10-32 work well. There's a little trick to it, as Doug figured out and recently communicated (...) (21 years ago, 11-Nov-03, to lugnet.technic)
|
| |
| | Re: polish version of mlcad
|
|
(...) Doceniam wysilek, dzieki! :) (21 years ago, 11-Nov-03, to lugnet.cad.mlcad, lugnet.robotics, lugnet.technic)
|
| |
| | Re: New MOC: Scania Garbage Truck
|
|
(...) You could use two belt wheels which you put together with the three friction pins. Then the problem is the steering outcome is too big. I still prefer my system while it doesn't require much space. It still is good enough because I don't drive (...) (21 years ago, 8-Nov-03, to lugnet.technic, lugnet.modelteam, FTX)
|
| |
| | Re: Has the technic "rotor" liftarm been discontinued or replaced?
|
|
"Philippe Hurbain" <philohome@free.fr> wrote in message news:Hny36E.zL9@lugnet.com... (...) on (...) from (...) Both the propellor and the 2L half beam are listed on that page though, see the bottom two lines: 2M Beam x2 3x120 Lever x2. In the (...) (21 years ago, 8-Nov-03, to lugnet.technic)
|
| |
| | threaded axle
|
|
Just wondered if damaged threaded axles can be cleaned down with a die or a thread restoring file??? If it can be,what die do I use or what is the pitch of the thread??? ,and no cheating Lego Australia don't hand out replacement/missing threaded (...) (21 years ago, 8-Nov-03, to lugnet.technic, FTX)
|
| |
| | Re: New MOC: Scania Garbage Truck
|
|
(...) Ok, here's a simple setup based on the 8466 steering :- (URL) And another with the other wheel attached :- (URL) The great thing about it is that it has a lot less unwanted movement with regard to hold the wheel in the steering arm since the (...) (21 years ago, 7-Nov-03, to lugnet.technic, lugnet.modelteam, FTX)
|
| |
| | Re: Steerable Walker
|
|
(...) Or in my case, living in Minnesota, it is what all of Winter is for. I like the alternate turns idea, because that way you also have 2/4/2/4 and avoid the gravity well, and vertical lurching. If you created a vertical launch mechanism used by (...) (21 years ago, 7-Nov-03, to lugnet.technic)
|
| |
| | Re: Steerable Walker
|
|
(...) I have been working on pneumatic designs for a quad walker, where it always has 2 feet on the ground, and the transition between pairs of feet has four feet on the ground. This prevents vertical lurching associated with 180 phase quadraped. (...) (21 years ago, 7-Nov-03, to lugnet.technic)
|
| |
| | Re: Steerable Walker
|
|
(...) Hi Tobbe, I think four legs would be enough: build it so the legs on a given side are 180 degrees out of phase. To turn, run only one side with the other side stopped so both legs are touching the ground. Driving in a strait line can be (...) (21 years ago, 7-Nov-03, to lugnet.technic)
|
| |
| | Throwbot Discs
|
|
Hello, I'm looking to finish my collection of throwbot discs. I haven't started yet so I still have discs # 1&2, so just about any offer will be taken. I'm looking for discs of all 8 throwbots. Just to encourage chat, Lego, for it's 2004 Bionicle (...) (21 years ago, 7-Nov-03, to lugnet.technic.slizer)
|
