 | | Re: New Technic stuff for 2003
|
|
(...) No more since TLC probably put the lid on. (...) One _small_ forklift truck, one wheel loader with a small bucket (might be new, not good with buckets - it's yellow) and one dump-truck (three axles, looks like the smallest balloon wheel from (...) (22 years ago, 13-Oct-02, to lugnet.technic)
|
| |
| | Re: Colored gears
|
|
(...) They appeared in several sets in the early 70's (URL) remember having an old idea book with plans for geared contraptions, but being frustrated because the gears were not available in the US at that time. I finally got my hands on some a few (...) (22 years ago, 15-Oct-02, to lugnet.technic)
|
| |
| | R: Front suspension and 3-or-more-speeds gearbox
|
|
It's compact, but, in my opinion, it's going to tear apart - this is because of the spring pulling away the axles from the dark gray connectors, when the suspension is pushed down ('m not considering the counter-action caused by the grip of the (...) (22 years ago, 15-Oct-02, to lugnet.technic)
|
| |
| | Re: New Version of 9V Geared Motor
|
|
(...) TJ (22 years ago, 15-Oct-02, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: Colored gears
|
|
These are old, pre-Technic gears. --Jack Gregory "Gaurav Thakur" <cp5670@3dap.com> wrote in message news:H415zC.CuA@lugnet.com... (...) unusual (...) the (...) pictures. (...) There (...) (22 years ago, 15-Oct-02, to lugnet.technic)
|
| |
| | Re: Colored gears
|
|
(...) These are quite old. I got some in my first LEGO set in the 1970's (Probably around 1975 or so). They are not modern Technic compatable. I still have several of each. They used to attach to the old wheels with metal axels. Eric Kingsley (22 years ago, 15-Oct-02, to lugnet.technic)
|
| |
| | Re: Front suspension and 3-or-more-speeds gearbox
|
|
Very elegant, I like it. - David (...) (22 years ago, 15-Oct-02, to lugnet.technic)
|
| |
| | Re: New Version of 9V Geared Motor
|
|
(...) From what I noticed... The permanent magnet is made by pressing together metal filings under pressure (my deduction, dunno if its true), and sometimes the magnet literally disintegrates, which causes metal filings to gum up the entire works. (...) (22 years ago, 15-Oct-02, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: New Version of 9V Geared Motor
|
|
(...) all were of the older type you have listed there. (one from the barcode set, two from the Mindstorms RDS and one extra I got from ebay) One thing that came to mind though was that the first version of these motors did have some problems with (...) (22 years ago, 15-Oct-02, to lugnet.robotics, lugnet.technic)
|
| |
| | Colored gears
|
|
I was just browsing around the Lugnet parts inventory and found some unusual gears that I had not seen before. They do not seem to be compatible with the normal gears as it looks like they have different types of teeth, and the standard axle (...) (22 years ago, 15-Oct-02, to lugnet.technic)
|
| |
| | Re: New Version of 9V Geared Motor
|
|
TJ, Mark has graciously allowed his picture to be added to my Brickshelf comparison page. Here's a deep link until the moderation is done: (URL) that helps, Clark Visit my Vintage Parts pages, submissions always welcome: (...) (22 years ago, 15-Oct-02, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: Front suspension and 3-or-more-speeds gearbox
|
|
what do u thing about my idea for back suspension? (URL) (22 years ago, 15-Oct-02, to lugnet.technic)
|
| |
| | Re: front wheel drive system
|
|
hi what about including this (URL) McLean" <vstar@iprimus.com.au> wrote in message news:H2KInz.I0H@lugnet.com... (...) a (...) (8 (...) steering (...) (22 years ago, 15-Oct-02, to lugnet.technic)
|
| |
| | Re: New Version of 9V Geared Motor
|
|
(...) an image of the new motor? thanks, TJ (22 years ago, 15-Oct-02, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: something i said?
|
|
(...) Nice one, Mike! I've added it to the gears page: (URL) (22 years ago, 15-Oct-02, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: New Version of 9V Geared Motor
|
|
I too, just got one of these, though it shipped in August from PITSCO. All of the things you mention. I thought I had a bad one. But I am giving it the benefit of the doubt, and it seems to operate well. I have not done a no-load rotation count test (...) (22 years ago, 15-Oct-02, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: Cartoon Network
|
|
(...) My 5 yr old absolutely glazes over when this comes one, as far as he is concerned it does not get any better than this. -Aaron- #279 (22 years ago, 15-Oct-02, to lugnet.mediawatch, lugnet.technic.bionicle)
|
| |
| | Re: something i said?
|
|
Nice work. I think you forgot to relocate the axles when you changed to the bevel gears. The way it's drawn the 5L axles penetrate the teeth of the 16-tooth gears and the bevel gears intrude on the adjacent axles. (22 years ago, 15-Oct-02, to lugnet.robotics, lugnet.technic)
|
| |
| | New Version of 9V Geared Motor
|
|
I hope this isn't old news - at least I couldn't find any mention of it here, so... While rummaging through a new copy of the Ultimate Builders Set (#3800), I noticed that the 9V mini-motor that came with the set was somewhat different than ones (...) (22 years ago, 15-Oct-02, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: something i said?
|
|
okay, i fixed a problem with semantics on the first part of the main page. the link to the new diff has been fixed so look, build, enjoy. m. p.s. sorry about the top posting, but it was my original message :) "Mike Fusion" <mikefusion@hotmail.com> (...) (22 years ago, 15-Oct-02, to lugnet.robotics, lugnet.technic)
|
