 | | Re: NQC 1.3 released - Command Center?
|
|
(...) I assume you meant "RcxCC". Last I heard from Mark, it will be "soon". I'm pretty sure you can just replace nqc.exe and rcx.nqh in RcxCC with the 1.3 versions. There won't be templates/hilighting for any new commands, but at least you will be (...) (25 years ago, 12-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC 1.3 released - Command Center?
|
|
(...) Say, when will NQCCC 1.3 be released? I'm completely hooked on the simple environment. DLC (25 years ago, 11-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: two task and while true
|
|
(...) Hmm: - I believe that, after main starts, unless you press IN_3 *very* quickly, that IN_3 will not be 1, hence stop wb will be chosen. Perhaps you want something like this? : task main { while (true) { wait(IN_3 == 1); // start motor wait(IN_3 (...) (25 years ago, 7-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: communication Linux - NQC - Cybermaster
|
|
(...) Yep, NQC assigns from 0 up. The listing (use -L) will print out the variable cross reference for an NQC program. Dave (25 years ago, 5-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: communication Linux - NQC - Cybermaster
|
|
(...) Thanks for your suggestions. Say, just what is variable 0? The first variable assigned? I should probably try to read some more about the internals of the RCX/Cybermaster, I suppose. Fredrik (25 years ago, 4-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: communication Linux - NQC - Cybermaster
|
|
(...) You can probably do anything you want with the [minimally documented] -raw option for nqc. You can use it to send arbitrary packets to the RCX or Cybermaster. For example, to query variable 0, you could do this: nqc -c -raw 120000 Of course, (...) (25 years ago, 2-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | communication Linux - NQC - Cybermaster
|
|
I'm running NQC on a Linux system. Is there any way to communicate between the computer and the Cybermaster mobile unit using this software? Or are there any other types of software I might consider to do this? Fredrik (25 years ago, 2-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: JAVA and Cybermaster ?
|
|
(...) Question: Why do you want to use JAVA with the CyberMaster? JAVA is similar to C++, which is was developed from C and which is the base language of NQC. What are you expecting to do with JAVA that can not be made with NQC? And if you are in a (...) (25 years ago, 2-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | JAVA and Cybermaster ?
|
|
I saw some Java stuff for the RCX. Is there soemthing for the Cybermaster? Stefan -- ***...*** Stefan Prescher prescher@hermes.fho-emden.de (25 years ago, 2-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | two task and while true
|
|
Hi I made a small programm task main if IN_3 ==1 start wb else stop wb task sb while (true) if () fwd(Out_a,7); I found out that the prgramms goes into the while loop but it never started the motor if I copied it into the main part it runs fine Is (...) (25 years ago, 2-May-99, to lugnet.robotics.rcx.nqc)
|
